?
Solved

cisco WS-C4507R

Posted on 2012-03-22
2
Medium Priority
?
691 Views
Last Modified: 2012-03-22
we have a cisco cisco WS-C4507R, just need some clarification if this switch is capable of poe.
we tried connecting a cisco ip phone and it would not power up, tried on serveral ports. is there some global config to turn POE on. below are some show command outputs

show power inline
Available:1400(w)  Used:0(w)  Remaining:1400(w)

Interface Admin  Oper            Power(Watts)     Device              Class
                            From PS    To Device                    
--------- ------ ---------- ---------- ---------- ------------------- -----

--------- ------ ---------- ---------- ---------- ------------------- -----

Totals:          0    on    0.0        0.0      


show power

Power                                             Fan      Inline
Supply  Model No          Type       Status       Sensor   Status
------  ----------------  ---------  -----------  -------  -------
PS1     PWR-C45-2800AC    AC 2800W   good         good     good  
PS2     PWR-C45-2800AC    AC 2800W   good         good     good  

Power supplies needed by system    : 1
Power supplies currently available : 2

Power Summary                      Maximum
 (in Watts)              Used     Available
----------------------   ----     ---------
System Power (12V)        308        1360
Inline Power (-50V)         0        1400
Backplane Power (3.3V)     40          40
----------------------   ----     ---------
Total                     348        2800



show module
Chassis Type : WS-C4507R

Power consumed by backplane : 40 Watts

Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
 1     2  Supervisor IV 1000BaseX (GBIC)         WS-X4515           JAE07460HNP
 3    48  10/100/1000BaseT (RJ45)                WS-X4548-GB-RJ45   JAE07460MH6
 7    48  1000BaseX SFP                          WS-X4448-GB-SFP    JAE1123KYM9

 M MAC addresses                    Hw  Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
 1 0007.0e34.1700 to 0007.0e34.1701 3.0 12.1(12r)EW  12.2(25)EWA6     Ok      
 3 000e.38fb.0c00 to 000e.38fb.0c2f 1.0                               Ok      
 7 001b.d546.9ab0 to 001b.d546.9adf 1.3                               Ok      

Mod  Redundancy role     Redundancy mode     Redundancy status
----+-------------------+-------------------+-------------------
 1   Active Supervisor   Non redundant       Active
0
Comment
Question by:Mars37
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 2

Accepted Solution

by:
BDC-Net earned 1200 total points
ID: 37754859
The chassis can support PoE, but your blade can't. The model number will have a V in it that indicates PoE (WS-X4548-GB-RJ45). Here is an example of one: WS-X4548-GB-RJ45V
0
 

Author Closing Comment

by:Mars37
ID: 37754871
thanks for quick response.
0

Featured Post

Ransomware Attacks Keeping You Up at Night?

Will your organization be ransomware's next victim?  The good news is that these attacks are predicable and therefore preventable. Learn more about how you can  stop a ransomware attacks before encryption takes place with our Ransomware Prevention Kit!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Hi there, This article summarizes what you need if you are going to set up your home or small business Network Attached Storage (NAS) to be accessible from the internet. Of course there are configuration differences based on your NAS or router ma…
Arrow Electronics was searching for a KVM  (Keyboard/Video/Mouse) switch that could display on one single monitor the current status of all units being tested on the rack.
In this tutorial you'll learn about bandwidth monitoring with flows and packet sniffing with our network monitoring solution PRTG Network Monitor (https://www.paessler.com/prtg). If you're interested in additional methods for monitoring bandwidt…
Monitoring a network: how to monitor network services and why? Michael Kulchisky, MCSE, MCSA, MCP, VTSP, VSP, CCSP outlines the philosophy behind service monitoring and why a handshake validation is critical in network monitoring. Software utilized …
Suggested Courses
Course of the Month14 days, 18 hours left to enroll

770 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question