Solved

Cisco VPN client on Windows 7 starter

Posted on 2012-03-26
9
1,112 Views
Last Modified: 2012-05-07
I have a win 7 starter minibook with the latest Cisco VPN client.
Using the Cisco client I can connect to the ASA, but can't pass traffic.
I turned off the firewall on the minibook, I have tried all of the adapters on the minibook also.
Does anyone know how to make this work?
0
Comment
Question by:mrbodjagles
  • 6
  • 2
9 Comments
 
LVL 6

Expert Comment

by:netjgrnaut
ID: 37766007
Can you be more specific about "can't pass traffic?"

Can you ping by IP address?  With the VPN connected, can you...

a. ping something on the public Internet via IP address (try 8.8.8.8)
b. ping the inside IP address of the ASA, again by IP address (not name)
0
 
LVL 17

Expert Comment

by:Garry-G
ID: 37766014
Did you do some debugging on either side of the VPN? If you do a "show crypto ipsec sa" on the firewall, do you see any packets coming in? On the client, are the configured inside addresses routed into the VPN?
0
 

Author Comment

by:mrbodjagles
ID: 37766485
1.  Yes I can ping to the public network from the clinet.
2.  No I cannont ping any address on the private network.
3.  If I do a "route print" from the client I do see the private network.
0
Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

 
LVL 6

Expert Comment

by:netjgrnaut
ID: 37766533
What about show  ip route on the ASA?  Do you see the VPN client?

I'm assuming that other VPN clients are working OK... is this true?  Can you validate that the minibook is picking up all the same IP/DNS/etc. info as the working clients?

Do you have priv access to the ASA?  Have you tried pinging the minibook VPN client IP?
0
 

Author Comment

by:mrbodjagles
ID: 37766707
Yes, other windows 7 clients are working fine.  As I said I connect to the ASA fine with the Windows 7 starter machine.  I just can't pass traffic.
The mini book does get the same ip/dns config of the working machines.
If I do a show crypto ipsec sa I do see the mini book client.

Any other ideas?
0
 

Author Comment

by:mrbodjagles
ID: 37768436
What services need to be running on the windows client for this to work?
Remote Access Connection?
What else?
0
 

Author Comment

by:mrbodjagles
ID: 37769629
Any other expert comments or suggestions?
I know someone has a answer for me.  Don't be shy.
0
 

Accepted Solution

by:
mrbodjagles earned 0 total points
ID: 37776522
Does anyone know if Windows 7 starter is even compatible with the Cisco VPN client?
0
 

Author Closing Comment

by:mrbodjagles
ID: 37936119
No answer
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Overview Often, we set up VPN appliances where the connected clients are on a separate subnet and the company will have alternate internet connections and do not use this particular device as the gateway for certain servers or clients. In this case…
This is an article about my experiences with remote access to my clients (so that I may serve them) and eventually to my home office system via Radmin Remote Control. I have been using remote access for over 10 years and have been improving my metho…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

803 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question