Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

Cisco Router 1841 Quality of service QoS - how to view

Posted on 2012-03-29
4
Medium Priority
?
329 Views
Last Modified: 2012-04-03
Hello Experts,

I ran into an issue trying to verify the actual consumption of video and voice on a remote site.  Please look at the configuration
1. VPN and internet work with no problem
2.Video is transmitted but it is kind of choppy.  

Problem:
I was under the impression that the following commands should give me QoS but it is not working because the ACL-s  do not have any hits .  I am attaching the configuration

class-map match-all SipVoice
 match access-group 198
class-map match-all Video
 match access-group 199


What am I doing wrong?  I want to limit the amount of bandwidth.
How do I view what is being processed in the QoS?

Thank you
RouterConfigl.txt
0
Comment
Question by:RandallVillalobos
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
4 Comments
 
LVL 20

Expert Comment

by:agonza07
ID: 37785642
Probably same as this:
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_26956855.html

Due to NAT you need to apply it the QoS on the inside interface.
0
 

Author Comment

by:RandallVillalobos
ID: 37797668
Hi good afternoon, it is not working :-(, I applied the Nat on the inside interface.

Do you recommend I run a specific debug?
0
 
LVL 20

Accepted Solution

by:
agonza07 earned 2000 total points
ID: 37797702
You need to apply QoS on the inside interface. NAT should stay the same.

After that you should see some hits on the ACLs. Just note that if you are sending these packets over the internet, you may have some problems there because the internet actually strips these QoS markings. You would only have control of which packets go out first in your network, and no control on how they arrive.

Use SDM to configure QoS on your router, or if you move the QoS commands over to the inside interface and you see your ACL hit count increasing then the problem may be with your ISP... on either end. Try to use G729 as your codec if you havent already, this should lower the bandwidth requirement.
0
 

Author Closing Comment

by:RandallVillalobos
ID: 37802640
Thanks! I'll run a quick check.
0

Featured Post

Supports up to 4K resolution!

The VS192 2-Port 4K DisplayPort Splitter is perfect for anyone who needs to send one source of DisplayPort high definition video to two or four DisplayPort displays. The VS192 can split and also expand DisplayPort audio/video signal on two or four DisplayPort monitors.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

During and after that shift to cloud, one area that still poses a struggle for many organizations is what to do with their department file shares.
Make the most of your online learning experience.
Both in life and business – not all partnerships are created equal. As the demand for cloud services increases, so do the number of self-proclaimed cloud partners. Asking the right questions up front in the partnership, will enable both parties …
Monitoring a network: how to monitor network services and why? Michael Kulchisky, MCSE, MCSA, MCP, VTSP, VSP, CCSP outlines the philosophy behind service monitoring and why a handshake validation is critical in network monitoring. Software utilized …

721 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question