Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

Ignored Packets in VLan 1

Posted on 2012-04-06
6
Medium Priority
?
718 Views
Last Modified: 2012-05-13
Hi all,
 
I have a Cisco WS-C2950-48,  and I have incrementing throttles and ignored on  VLAN 1 interface.  Vlan 1 is a managament interface, some time
when I try to Access I can't.
 
2950#show int vlan 1
Vlan1 is up, line protocol is up
  Internet address is 10.0.0.146/16
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  30 second input rate 36000 bits/sec, 52 packets/sec
  30 second output rate 17000 bits/sec, 23 packets/sec
     297870558 packets input, 1596814696 bytes, 0 no buffer
     Received 195554838 broadcasts (0 IP multicast)
     0 runts, 0 giants, 1607875 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 98455174 ignored
     76743540 packets output, 3185572576 bytes, 0 underruns
     0 output errors, 2 interface resets
     0 output buffer failures, 0 output buffers swapped out
 
Clients are not having any troubles.
 
 
CPU utilization it's OK.
 
 
Thanks in advance.
0
Comment
Question by:BCN_2012
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 3
6 Comments
 
LVL 15

Expert Comment

by:Nayyar HH (CCIE RS)
ID: 37815749
Can you post "show ip traffic" output ?
0
 

Author Comment

by:BCN_2012
ID: 37815860
Yes, thanks for reply,

show ip traffic
IP statistics:
  Rcvd:  1074460 total, 152824 local destination
         0 format errors, 0 checksum errors, 0 bad hop count
         0 unknown protocol, 921636 not a gateway
         0 security failures, 0 bad options, 51 with options
  Opts:  0 end, 0 nop, 0 basic security, 0 loose source route
         0 timestamp, 0 extended security, 0 record route
         0 stream ID, 0 strict source route, 51 alert, 0 cipso
         0 other
  Frags: 0 reassembled, 0 timeouts, 0 couldn't reassemble
         0 fragmented, 0 couldn't fragment
  Bcast: 140851 received, 3 sent
  Mcast: 0 received, 0 sent
  Sent:  12442 generated, 0 forwarded
  Drop:  382 encapsulation failed, 0 unresolved, 0 no adjacency
         0 no route, 0 unicast RPF, 0 forced drop
  Drop:  0 packets with source IP address zero

ICMP statistics:
  Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 5 unreachable
        1693 echo, 440 echo reply, 0 mask requests, 0 mask replies, 0 quench
        0 parameter, 0 timestamp, 0 info request, 0 other
        0 irdp solicitations, 0 irdp advertisements
  Sent: 0 redirects, 0 unreachable, 440 echo, 1693 echo reply
        0 mask requests, 0 mask replies, 0 quench, 0 timestamp
        0 info reply, 0 time exceeded, 0 parameter problem
        0 irdp solicitations, 0 irdp advertisements

UDP statistics:
  Rcvd: 147949 total, 0 checksum errors, 140851 no port
  Sent: 7407 total, 0 forwarded broadcasts

TCP statistics:
  Rcvd: 2737 total, 0 checksum errors, 2 no port
  Sent: 2904 total

ARP statistics:
  Rcvd: 2827378 requests, 45 replies, 0 reverse, 0 other
  Sent: 361 requests, 1724 replies (0 proxy), 0 reverse
0
 
LVL 15

Expert Comment

by:Nayyar HH (CCIE RS)
ID: 37819913
I think there might be a host on VLAN1 sending excessive broadcast,

65% of packets received on VLAN1 is broadcast

Try to track down the host by finding out which connected port in VLAN1 has a very high "received broadcast" value

Command:

sh interfaces | i lan|ther|broad

You could look to enable broadcast storm-control
0
When ransomware hits your clients, what do you do?

MSPs: Endpoint security isn’t enough to prevent ransomware.
As the impact and severity of crypto ransomware attacks has grown, Webroot fought back, not just by building a next-gen endpoint solution capable of preventing ransomware attacks but also by being a thought leader.

 
LVL 15

Expert Comment

by:Nayyar HH (CCIE RS)
ID: 37819919
0
 

Accepted Solution

by:
BCN_2012 earned 0 total points
ID: 37821004
Hi, thanks for reply again,

I think there is a memory problem in switch:

show buffers failures
Caller       Pool          Size      When
0x802D7634  Large            170    08:07:37
0x802D7634  Huge             170    08:07:37
0x802D7634  Middle           170    07:07:37
0x802D7634  Middle           170    05:33:54
0x802D7634  Middle           170    03:56:43
0x802D7634  Middle           170    03:56:43
0x802D7634  Middle           170    00:12:26
0x802D7634  Middle           178    00:12:26
0x802D7634  Middle           170    00:12:26
0x802D7634  Middle           170    00:12:26

2950#show region address 0x802D7634
Address 0x802D7634 is located physically in :
 
  Name  : text
  Class : IText
  Media : R/W
  Start : 0x80010000
  End   : 0x8056FA63
  Size  : 0x0055FA64
0
 

Author Closing Comment

by:BCN_2012
ID: 37961895
Good answers
0

Featured Post

Learn how to optimize MySQL for your business need

With the increasing importance of apps & networks in both business & personal interconnections, perfor. has become one of the key metrics of successful communication. This ebook is a hands-on business-case-driven guide to understanding MySQL query parameter tuning & database perf

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

So, you're experiencing issues on your network and you've decided that you need to perform some tests to determine whether your cabling is good.  You're likely thinking that you may need to spend money which you probably don't have on hiring/purchas…
#Citrix #Citrix Netscaler #HTTP Compression #Load Balance
Here's a very brief overview of the methods PRTG Network Monitor (https://www.paessler.com/prtg) offers for monitoring bandwidth, to help you decide which methods you´d like to investigate in more detail.  The methods are covered in more detail in o…
Monitoring a network: why having a policy is the best policy? Michael Kulchisky, MCSE, MCSA, MCP, VTSP, VSP, CCSP outlines the enormous benefits of having a policy-based approach when monitoring medium and large networks. Software utilized in this v…
Suggested Courses

721 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question