Solved

cisco dynamic route

Posted on 2012-04-08
6
218 Views
Last Modified: 2012-07-26
Dear

 as shown this Diagram

I have this network i want connect through EIGRP dynamic route .
I want all my network  go from router R2 --- R4 --- R10 to out side
and same from out side to R10 --- R4 ---R2


how I can to that  I give manual select which path it go , if one of active link goes down go to standby for both site A & B
diagram.jpg
0
Comment
Question by:memo12345678
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 4
6 Comments
 

Accepted Solution

by:
memo12345678 earned 0 total points
ID: 37821276
please write for me config
0
 
LVL 7

Expert Comment

by:diepes
ID: 37823701
To Force traffic to take the top route except for a failure, just make the cost for the bottom path high.

For EIGRP on R3 and R5 add on all interfaces in and out.

delay 100
0
 

Author Comment

by:memo12345678
ID: 37823992
really I donot understand can do write commend for this example ?
0
MIM Survival Guide for Service Desk Managers

Major incidents can send mastered service desk processes into disorder. Systems and tools produce the data needed to resolve these incidents, but your challenge is getting that information to the right people fast. Check out the Survival Guide and begin bringing order to chaos.

 

Author Comment

by:memo12345678
ID: 37826439
r12#traceroute 1.1.1.1

      1  62.201.242.5       44 msec 32 msec 32 msec
      2  172.241.1.2         60 msec 56 msec 48 msec
  3  4.4.4.3                 108 msec 120 msec 92 msec
      4  10.201.240.1        100 msec *  116 msec


and

R10#tracer  62.201.242.11


  1  10.201.240.3            48 msec 28 msec 28 msec
  2  4.4.4.1                       60 msec 84 msec 36 msec
 3 172.241.1.4           92 msec 88 msec 92 msec
  4  62.201.242.11           [AS 65532] 104 msec

I want traffic go to Upload and download go to R3 --- R5 ---R10 how do it

see my config
R2#show ip route
172.241.0.0/28 is subnetted, 1 subnets
C       172.241.1.0 is directly connected, FastEthernet0/0
      172.240.0.0/28 is subnetted, 1 subnets
D       172.240.240.0 [90/1538560] via 4.4.4.4, 00:08:00, FastEthernet0/1
                                   [90/1538560] via 4.4.4.3, 00:08:00, FastEthernet0/1
         62.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C       62.201.243.0/29 is directly connected, FastEthernet0/1
S       62.201.242.0/24 [1/0] via 172.241.1.4
D*EX    0.0.0.0/0 [170/3865600] via 4.4.4.4, 00:08:02, FastEthernet0/1
                                  [170/3865600] via 4.4.4.3, 00:08:02, FastEthernet0/1

R2# show run config
inter fast 0/1
delay 5000
R4# show run config
inter fast 0/1
delay 5000

R4#show ip eigrp neighbors
IP-EIGRP neighbors for process 20
H   Address                 Interface       Hold Uptime   SRTT   RTO  Q  Seq
                                            (sec)                (ms)             Cnt Num
3   4.4.4.2                         Fa0/1             10 00:14:30   92   552  0  50
2   4.4.4.1                         Fa0/1             11 00:14:30   88   528  0  59
1   4.4.4.4                         Fa0/1             13 00:14:31   56   336  0  80
0   172.240.240.2            Fa1/0             13 00:14:31   50   450  0  78
 
R4#show ip route

     172.240.0.0/28 is subnetted, 1 subnets
C       172.240.240.0 is directly connected, FastEthernet1/0
     10.0.0.0/24 is subnetted, 1 subnets
C       10.201.240.0 is directly connected, FastEthernet0/0
     62.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C       62.201.243.0/29 is directly connected, FastEthernet0/1
D EX    62.201.242.0/24
           [170/1561600] via 4.4.4.2, 00:01:22, FastEthernet0/1
           [170/1561600] via 4.4.4.1, 00:01:22, FastEthernet0/1
S*   0.0.0.0/0 [1/0] via 10.201.240.1



but still traffic doesn't  go to R2 -- R4 why !!!
0
 
LVL 16

Expert Comment

by:SteveJ
ID: 37942082
Are R7, R8 and R9 routing or just switching? Your diagram is a little unclear in that regard. If I want to influence the route, I would start at R1 to make sure the path went to R2, then I would add "delay" in R3 f0/1 and f0/0 and R5 f1/0, f0/1 and F0/0.



Good luck,
Steve
0
 

Author Closing Comment

by:memo12345678
ID: 38226019
d
0

Featured Post

Free Tool: Path Explorer

An intuitive utility to help find the CSS path to UI elements on a webpage. These paths are used frequently in a variety of front-end development and QA automation tasks.

One of a set of tools we're offering as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This article is a guide to configure bridging on Cisco Routers.  This is something I never knew was possible until after making a few phone calls to Cisco.  Using bridging saved our company money by not requiring us to purchase a new switch.  Bridgi…
The Cisco RV042 router is a popular small network interfacing device that is often used as an internet gateway. Network administrators need to get at the management interface to make settings, change passwords, etc. This access is generally done usi…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

751 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question