Solved

Watchguard x750e routing problems

Posted on 2012-04-10
4
493 Views
Last Modified: 2013-01-16
I'm working with a Watchguard x750e (11.1.3) and I'm having routing problems configuring a load balancer.

Using a 1-to-1 NAT and a rule with a Static NAT, I can reach one server but if I remove the 1-to-1 NAT and add the load balancer option (round robin) there is no way to reach the servers.

I tried with two network cards on the servers, but, due all the issues right now is just one network card (a pretty basic setup)

Any suggestions?
0
Comment
Question by:moralesrd
  • 2
  • 2
4 Comments
 
LVL 32

Expert Comment

by:dpk_wal
ID: 37831812
You can only configure server load balancing with static NAT.

Have a look at link:
http://www.watchguard.com/help/docs/wsm/11/en-US/Content/en-US/nat/server_load_balancing_config_c.html

Thank you.
0
 

Author Comment

by:moralesrd
ID: 37840486
According to your answer and due I have a PPoE connection it will be necessary to install an additional router between the bridge and the watchguard, to assign a fixed IP address, correct?
0
 
LVL 32

Accepted Solution

by:
dpk_wal earned 500 total points
ID: 37841603
There are few flavors of NAT on WG:
static NAT; where based on public IP and port/protocol pair you forward inbound traffic to different internal server IP/port/protocol.
1-1 NAT; where you map one public IP to one specific internal server IP for ALL ports/protocols.

What I meant is that you should use static NAT and NOT 1-1 NAT as you mentioned in your original post.

Look at article for exact configuration steps.

Thank you.
0
 

Author Comment

by:moralesrd
ID: 37841943
I already did follow those steps, and the problem is due I'm using a PPoE connection I cannot set an static IP (due I have to provide user/pwd) and I was reffering to the 1-to-1 NAT example to indicates that the incoming traffic is working, but for an unknown reason in a load balancer mode without 1-to-1 there is not... to me seems like there is routing step that I'm missing but don't know exactly where.
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Stuck in INIT/DROTHER 2 53
EIGRP STUB 19 86
Need a device to send message to phone when power is out 3 104
Cisco WLAN 5520 licensing 10 60
There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
Before I go to far, let's explain HA (High Availability) and why you should consider it.  High availability is the mechanism used to provide redundancy to any service at the same site and appears as a single service to the users of that service.  As…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

821 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question