Solved

NDR message to excess message size

Posted on 2012-04-12
10
1,886 Views
Last Modified: 2012-05-07
Hi ,

I have two hub transport server & I am getting NDR message for Excess size limit from one of the Server, attached below error message

Final-Recipient: rfc822;padas6@abc.com
Action: failed
Status: 5.0.0 (permanent failure)
Remote-MTA: dns; [10.100.23.51]
Diagnostic-Code: smtp; 5.1.0 - Unknown address error 552-'5.3.4 Message size exceeds fixed maximum message size' (delivery attempts: 0)

I have checked all the messgae size setting in global & receive connector settings.

Please help us to reolve the issue.
0
Comment
Question by:padas6
  • 6
  • 4
10 Comments
 
LVL 9

Expert Comment

by:Geodash
Comment Utility
Have you increased the message header size as well?
0
 
LVL 9

Accepted Solution

by:
Geodash earned 280 total points
Comment Utility
Set-ReceiveConnector MaxHeaderSize Exchange 2007 RTM and Exchange 2007 SP1 64 KB

http://social.technet.microsoft.com/Forums/en-US/exchangesvradmin/thread/57d926f5-c80d-4daa-8b3b-2a21f4781c25

You may have to increase the message header size limit too. This was happening to a client of mine and this resolved their issue
0
 

Author Comment

by:padas6
Comment Utility
Hi Geodash,

Soory for delay response.

I have check both of my Hub Transport Server & it is defined message header size 64KB in both the Server, although I have increase it 200KB for my problemtic node.

Let see the effect tomorrow.
0
 

Author Comment

by:padas6
Comment Utility
only for the Default Receive connector.
0
 

Author Comment

by:padas6
Comment Utility
Hi

Even after change the message header size form 64 to 200 KB same result.

The following message to <padas6@abc.com> was undeliverable.
The reason for the problem:
5.1.0 - Unknown address error 552-'5.3.4 Message size exceeds fixed maximum message size'

Final-Recipient: rfc822;padas6@abc.com
Action: failed
Status: 5.0.0 (permanent failure)
Remote-MTA: dns; [10.100.23.51]
Diagnostic-Code: smtp; 5.1.0 - Unknown address error 552-'5.3.4 Message size exceeds fixed maximum message size' (delivery attempts: 0)
0
How your wiki can always stay up-to-date

Quip doubles as a “living” wiki and a project management tool that evolves with your organization. As you finish projects in Quip, the work remains, easily accessible to all team members, new and old.
- Increase transparency
- Onboard new hires faster
- Access from mobile/offline

 
LVL 9

Expert Comment

by:Geodash
Comment Utility
did you restart the transport service?
0
 

Author Comment

by:padas6
Comment Utility
The transport Service was off & start the Service after configuration changes.

Do I restsrt once again.
0
 
LVL 9

Expert Comment

by:Geodash
Comment Utility
I know when i changed the settings, it was not instant. But I do not remember if I restarted the exchange services or bounced the server.
0
 

Author Comment

by:padas6
Comment Utility
I have restsrted the Services & tested two mails , one is through & another is blocked, may be through one is passing through the another server or not.

NDR message is shows the faulty Server only.
0
 

Author Closing Comment

by:padas6
Comment Utility
Thanks for the guideline, it workes for my setup as well.
0

Featured Post

Do email signature updates give you a headache?

Do you feel like all of your time is spent managing email signatures? Too busy to visit every user’s desk to make updates? Want high-quality HTML signatures on all devices, including on mobiles and Macs? Then, let Exclaimer solve all your email signature problems today!

Join & Write a Comment

Disabling the Directory Sync Service Account in Office 365 will stop directory synchronization from working.
Local Continuous Replication is a cost effective and quick way of backing up Exchange server data. The following article describes the steps required to configure Local Continuous Replication. Also, the article tells you how to restore from a backup…
In this video we show how to create a Distribution Group in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.: First we need to log into the Exchange Admin Center. Navigate to the Recipients >>…
In this video we show how to create a Shared Mailbox in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.: First we need to log into the Exchange Admin Center. Navigate to the Recipients >> Sha…

772 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

10 Experts available now in Live!

Get 1:1 Help Now