• Status: Solved
  • Priority: Medium
  • Security: Public
  • Views: 1757
  • Last Modified:

Adtran switch routing between VLAN's

Currently have an Adtran 1224STR PWR, running  F/W 13.07.00

The primary network block is 192.168.113.0/24, with a g/w of 192.168.113.254

I am adding a second VLAN, VLAN2 with a network block of 192.168.213.0/24 and it is communicating correctly from the devices on the VLAN2 segment, to the switch.

I have enabled IP routing in the VLAN2 config, and the VLAN gateway is 0.0.0.0, which is same as the VLAN1 segment.

If I ping from the Adtran CLI, I can ping from the primary network to the gateway, but not the VLAN2 segment.
There is no firewall enabled on the router.

What am I missing to allow routing of the VLAN2 traffic, from VLAN2 thru the Adtran to the gateway?

Am I correct in expecting the router at .254 to see traffic from VLAN2 with a source address of the Adtran?
0
dkuhlman
Asked:
dkuhlman
  • 4
  • 4
1 Solution
 
FideliusCommented:
Hello,

On page 2 in https://supportforums.adtran.com/servlet/JiveServlet/downloadBody/2054-102-1-2172/NetVanta%201224%20PWR%20Series%20Power%20over%20Ethernet%20Quick%20Start%20Guide.pdf you can find:

NOTE: Depending on your configuration, you may need to set a default gateway as well using the (config)#ip default gateway command. If IP routing is enabled on the unit, do NOT set a default gateway.

So try to remove default gateway from VLANs.

Regards!
0
 
FideliusCommented:
Also please post output of:
#show ip route

With ip routing enabled (which is by default), only thing you need to do on switch is to configure IP address in each VLAN.
Each configured IP address should be default gateway for corresponding VLANs hosts.

Regards!
0
 
dkuhlmanAuthor Commented:
Here is the result of the #show ip route command:

#show ip routeCodes: C - connected, S - static, R - RIP, O - OSPF, B - BGP
       IA - OSPF inter area, N1 - OSPF NSSA external type 1
       N2 - OSPF NSSA external type 2, E1 - OSPF external type 1
       E2 - OSPF external type 2

Gateway of last resort is 192.168.113.254 to network 0.0.0.0

S    0.0.0.0/0 [1/0] via 192.168.113.254, vlan 1
C    10.0.0.0/24 is directly connected, vlan 100
C    192.168.113.0/24 is directly connected, vlan 1
S    192.168.114.0/24 [1/0] via 192.168.113.2, vlan 1
C    192.168.213.0/24 is directly connected, vlan 2
0
Prepare for an Exciting Career in Cybersecurity

Help prevent cyber-threats and provide solutions to safeguard our global digital economy. Earn your MS in Cybersecurity. WGU’s MSCSIA degree program curriculum features two internationally recognized certifications from the EC-Council at no additional time or cost.

 
FideliusCommented:
For hosts in VLAN2 gateway should be IP address of switch in VLAN2.
I assume it is 192.168.213.1 or 254.
0
 
dkuhlmanAuthor Commented:
Here's a screenshot of how I configured VLAN2
vlan2.png
0
 
dkuhlmanAuthor Commented:
Here's the routing config from the GUI
routing.png
0
 
FideliusCommented:
Remove static route:
192.168.213.0 255.255.255.0 192.168.113.254

As this subnet is directly connected.
0
 
dkuhlmanAuthor Commented:
We've tried removing that static route (and about 100 other configuration variations) but still don't have this working.  Can we call Adtran directly for support?
0

Featured Post

Technology Partners: We Want Your Opinion!

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

  • 4
  • 4
Tackle projects and never again get stuck behind a technical roadblock.
Join Now