yaminz66
asked on
Power source for Cisco Catalyst 2950G-24
HI
I have couple of these switches, but cannot find the power source for this. Does anyone know how I can power them up?
Regards
Yamin
I have couple of these switches, but cannot find the power source for this. Does anyone know how I can power them up?
Regards
Yamin
ASKER
Hi
Yes that is why I am asking. I cant see the power socket,.
Here is a picture of the item
http://www.google.co.uk/imgres?q=Cisco+Catalyst+2950G-24&um=1&hl=en&sa=N&tbo=d&biw=1680&bih=925&tbm=isch&tbnid=kAxomLa_xXuKUM:&imgrefurl=http://www.networkbrokers.com.au/cisco/switches/ws-c2950/&docid=ZC1YBs1Pog1SaM&imgurl=http://www.networkbrokers.com.au/media/catalog/category/WS-C2950G-48-EI.jpg&w=200&h=150&ei=zZHUUK75K8XG0QWo4YGYAQ&zoom=1&iact=hc&vpx=380&vpy=323&dur=181&hovh=120&hovw=160&tx=108&ty=89&sig=111288753820467927238&page=1&tbnh=120&tbnw=155&start=0&ndsp=45&ved=1t:429,r:11,s:0,i:121
Regards
Yamin
Yes that is why I am asking. I cant see the power socket,.
Here is a picture of the item
http://www.google.co.uk/imgres?q=Cisco+Catalyst+2950G-24&um=1&hl=en&sa=N&tbo=d&biw=1680&bih=925&tbm=isch&tbnid=kAxomLa_xXuKUM:&imgrefurl=http://www.networkbrokers.com.au/cisco/switches/ws-c2950/&docid=ZC1YBs1Pog1SaM&imgurl=http://www.networkbrokers.com.au/media/catalog/category/WS-C2950G-48-EI.jpg&w=200&h=150&ei=zZHUUK75K8XG0QWo4YGYAQ&zoom=1&iact=hc&vpx=380&vpy=323&dur=181&hovh=120&hovw=160&tx=108&ty=89&sig=111288753820467927238&page=1&tbnh=120&tbnw=155&start=0&ndsp=45&ved=1t:429,r:11,s:0,i:121
Regards
Yamin
ASKER
Hi
lol - no its not.
lol - no its not.
ASKER
I will post the actual pictures of it tomorrow.
Is there a small four-pin block in the location that the AC power connector would be?
If so, you've got a 2950G-24-DC. It has a DC power supply.
If so, you've got a 2950G-24-DC. It has a DC power supply.
ASKER
HI
Here are the images - There seems to be two types of connection at the back.
I think you are right donjohnson, in that case where do I get that from ? Why was it not supplied with the Switches?
Regards
IMG-1717.JPG
IMG-1716.JPG
IMG-1718.JPG
Here are the images - There seems to be two types of connection at the back.
I think you are right donjohnson, in that case where do I get that from ? Why was it not supplied with the Switches?
Regards
IMG-1717.JPG
IMG-1716.JPG
IMG-1718.JPG
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
HI
Thank you so much. I have been supplied with the 4 pin L-Shaped socket, I assume that goes into the socket. So where are these cables fed into? I assume this is how the CISCO supplies them and its up to the user to install them in that way?
Regards
Yamin
Thank you so much. I have been supplied with the 4 pin L-Shaped socket, I assume that goes into the socket. So where are these cables fed into? I assume this is how the CISCO supplies them and its up to the user to install them in that way?
Regards
Yamin
So where are these cables fed into?They would be connected to the DC power source (typically 48 vdc).
Or am I misunderstanding the question?