janhoedt
asked on
ZFS Nexenta for esxi: cannot install napp-it
Hi,
I have nexenta installed on a hp proliant NL40.
I would like to install napp-it, I cannot when I login via root
wget -O - www.napp-it.org/nappit | perl => it says command unknown or wrong
When I login via admin, it shows this
admin@Nexenta:~$ wget -O - www.napp-it.org/nappit | perl
--13:55:24-- http://www.napp-it.org/nappit
=> `-'
Resolving www.napp-it.org... 80.67.28.3, 2a00:1158:0:300:9a63::1
Connecting to www.napp-it.org|80.67.28.3|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 26,763 (26K) [text/plain]
100%[===================== ========== =====>] 26,763 --.--K/s
13:55:24 (311.36 KB/s) - `-' saved [26763/26763]
But it is not installed: page http://ipofmyserver:81 shows nothing.
Please advise.
J.
I have nexenta installed on a hp proliant NL40.
I would like to install napp-it, I cannot when I login via root
wget -O - www.napp-it.org/nappit | perl => it says command unknown or wrong
When I login via admin, it shows this
admin@Nexenta:~$ wget -O - www.napp-it.org/nappit | perl
--13:55:24-- http://www.napp-it.org/nappit
=> `-'
Resolving www.napp-it.org... 80.67.28.3, 2a00:1158:0:300:9a63::1
Connecting to www.napp-it.org|80.67.28.3|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 26,763 (26K) [text/plain]
100%[=====================
13:55:24 (311.36 KB/s) - `-' saved [26763/26763]
But it is not installed: page http://ipofmyserver:81 shows nothing.
Please advise.
J.
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
you will need Napp-it 0.8 to install on Nexenta!
This year 0.9 has been released, which does not support Nexenta!
hence the message, which states use 0.8!
This year 0.9 has been released, which does not support Nexenta!
hence the message, which states use 0.8!
ASKER
wget -O - http://www.napp-it.org/nappit08 | perl then?
Didn't work for me, result is the same.
Didn't work for me, result is the same.
ASKER
Ok
ASKER
Actually I did, but tried it a second time, result is the same:
---
step 1a: check os, setup napp-it or updating to the most current version now
please wait uname -a: SunOS Nexenta 5.11 NexentaOS_134f i86pc i386 i86pc Solaris
NexentaCore is supported up to napp-it 0.8 - use napp-it 0.8!!
root@Nexenta://root#
---
---
step 1a: check os, setup napp-it or updating to the most current version now
please wait uname -a: SunOS Nexenta 5.11 NexentaOS_134f i86pc i386 i86pc Solaris
NexentaCore is supported up to napp-it 0.8 - use napp-it 0.8!!
root@Nexenta://root#
---
that setup file is NOT 0.8!
looks like 0.9!
tested this afternoon and confirmed.
looks like 0.9!
tested this afternoon and confirmed.
ASKER
Ok, then I must have done something wrong. Will recheck & post the steps I took.
ASKER
Ok, worked fine now!
Note: don't see much added value in nappit (for a newbie) versus Nexenta though.
Note: don't see much added value in nappit (for a newbie) versus Nexenta though.
The Nexenta GUI is very good.
ASKER
Replace http://www.napp-it.org/nappit with http://www.napp-it.org/nappit08 for nexenta.
ASKER
BUT....there does seem to be an issue with the current detection routines in step 1a, which states using napp-it 0.8!
No idea what you mean by that, what it implies or how I should correct, please advise on that.