?
Solved

MDT 2010 Multicast task sequence get stuck

Posted on 2013-01-08
10
Medium Priority
?
2,721 Views
Last Modified: 2013-12-12
Dear Experts,

I got a trouble with MDT when I do multicast transmission task to deploy OS onto clients.
When I run MDT multicast transmission task, it always stuck at "Attempting multicast transfer" with a little bit percentages (Usually 4% or 6%). I see no traffic go through network interface when monitor. I've tried using direct connection between server and client (using cross-over cable) but nothing change.
Could you please help me pass this step
I'm using Windows server 2008 R2, MDT2010 to deploy Windows 7. I already installed WDS role and WAIK

Thank you all
0
Comment
Question by:rvc-it
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 5
  • 3
10 Comments
 
LVL 17

Expert Comment

by:James Haywood
ID: 38789409
What are your multicast settings? Are the relevant firewall ports open?
0
 

Author Comment

by:rvc-it
ID: 38799710
Dear hhaywood000

I'm sorry for may late response. All settings I left they as default, no special settings, I already turn off firewall. I tried connecting server and client directly by using cross-over cable but not thing change.
Thank you for your help
0
 
LVL 17

Expert Comment

by:James Haywood
ID: 38800947
Does the whole system work when just deploying normally without bringing in multicast?
0
Problems using Powershell and Active Directory?

Managing Active Directory does not always have to be complicated.  If you are spending more time trying instead of doing, then it's time to look at something else. For nearly 20 years, AD admins around the world have used one tool for day-to-day AD management: Hyena. Discover why

 

Author Comment

by:rvc-it
ID: 38826049
Dear hhaywood000

I'm sorry for my late response. Actually, it cannot work even though deploying normally.
It always stuck at few percents. I have tried installing a new server for testing but it still doesn't work.
I'm going to test deploying Windows 7 32bit to make sure the problem is not come from architecture. I'll update the status for you

Thank you for your help
0
 
LVL 17

Expert Comment

by:James Haywood
ID: 38826240
No problems. Try this in order

WDS only
MDT simple client install
A new install.wim
0
 

Author Comment

by:rvc-it
ID: 38842196
Dear hhaywood000

I've finished testing as your recommend. I installed a fresh Server and tried from the beginning and have some result
WDS only: worked
MDT simple client install: worked. I can capture image of new installed machine but when I use multicast and it stuck again. Maybe I have a mistake in some step.
I installed Lab as order: Windows Server > Join domain > Windows AIK > DHCP > WDS > MDT then I add Installation source to MDT.
I'll check them again
Thank you for your strong support

Best regards,
RVC-IT
0
 
LVL 17

Expert Comment

by:James Haywood
ID: 38842858
Do your switches support multicast? Is it turned on?
0
 
LVL 17

Accepted Solution

by:
James Haywood earned 2000 total points
ID: 38842868
Also do you have multicast support turned on within MDT?

This is a good link showing how to test the multicast transmissions from WDS

http://systemscenter.ru/mdt2012.en/opti3usemultwithmdtandthewindser.htm
0

Featured Post

Is Your AD Toolbox Looking More Like a Toybox?

Managing Active Directory can get complicated.  Often, the native tools for managing AD are just not up to the task.  The largest Active Directory installations in the world have relied on one tool to manage their day-to-day administration tasks: Hyena. Start your trial today.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This article is in regards to the Cisco QSFP-4SFP10G-CU1M cables, which are designed to uplink/downlink 40GB ports to 10GB SFP ports. I recently experienced this and found very little configuration documentation on how these are supposed to be confi…
If you're a modern-day technology professional, you may be wondering if certifications are really necessary. They are. Here's why.
Michael from AdRem Software explains how to view the most utilized and worst performing nodes in your network, by accessing the Top Charts view in NetCrunch network monitor (https://www.adremsoft.com/). Top Charts is a view in which you can set seve…
In this brief tutorial Pawel from AdRem Software explains how you can quickly find out which services are running on your network, or what are the IP addresses of servers responsible for each service. Software used is freeware NetCrunch Tools (https…
Suggested Courses

764 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question