Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people, just like you, are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
Solved

Configuring Dynamic NAT, PAT, or Identity NAT

Posted on 2013-01-14
2
654 Views
Last Modified: 2013-02-01
Hello Experts

To configure a dynamic NAT, PAT, or identity NAT rule, I need to perform the following steps:

Step 1 From the Configuration > Firewall > NAT Rules pane, choose Add > Add Dynamic NAT Rule.
 
The Add Dynamic NAT Rule dialog box appears.


However, when I click on Add I don't get the option to Add Dynamic Nat Rule

To see the options I get please see attachment.

Can someone please explain what I'm missing.

The following is a capture of the show version:

ciscoasa# show ver

Cisco Adaptive Security Appliance Software Version 8.4(2) <system>
Device Manager Version 6.4(1)

Compiled on Wed 15-Jun-11 18:17 by builders
System image file is "Unknown, monitor mode tftp booted image"
Config file at boot was "startup-config"

ciscoasa up 16 mins 57 secs

Hardware:   ASA 5520, 1024 MB RAM, CPU Pentium II 1000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash unknown @ 0x0, 0KB


 0: Ext: GigabitEthernet0    : address is 00ab.a72f.0100, irq 0
 1: Ext: GigabitEthernet1    : address is 00ab.a72f.0101, irq 0
 2: Ext: GigabitEthernet2    : address is 0000.ab6d.9802, irq 0
 3: Ext: GigabitEthernet3    : address is 0000.abd4.8803, irq 0
 4: Ext: GigabitEthernet4    : address is 0000.abe3.8804, irq 0
 5: Ext: GigabitEthernet5    : address is 0000.abb8.a605, irq 0

Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 100            perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Active/Active  perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 2              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 5000           perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 5000           perpetual
Total VPN Peers                   : 0              perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual

This platform has an ASA 5520 VPN Plus license.

Serial Number: 123456789AB
Running Permanent Activation Key: 0x4a3ec071 0x0d86fbf6 0x7cb1bc48 0x8b48b8b0 0xf317c0b5
Configuration register is 0x0
Configuration has not been modified since last system restart.
ciscoasa#

Cheers

Carlton
ciscoasa2.jpg
0
Comment
Question by:cpatte7372
2 Comments
 
LVL 37

Accepted Solution

by:
ArneLovius earned 500 total points
ID: 38778377
I think you are confusing how this would work on versions prior to 8.3 and post 8.3 in ASDM

On versions post 8.3 the NAT type is determined in the NAT rule itself.
0
 

Author Closing Comment

by:cpatte7372
ID: 38842990
Cheers
0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Hello , This is a short article on how would you go about enabling traceoptions on a Juniper router . Traceoptions are similar to Cisco debug commands but these traceoptions are implemented in Juniper networks router . The following demonstr…
This article offers some helpful and general tips for safe browsing and online shopping. It offers simple and manageable procedures that help to ensure the safety of one's personal information and the security of any devices.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

839 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question