Solved

configuring ports

Posted on 2013-01-18
7
220 Views
Last Modified: 2014-11-10
I have a hp procurve switch that is configured for two seperate vlans.
We have a Vlan for staff and a Vlan for visitors. some ports are configured for the staff network the other ports are configured for visitors network. im trying to have the switch show nothing but the staff vlan. how can i make the changes thats needed?
0
Comment
Question by:armsteadw
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
7 Comments
 
LVL 17

Expert Comment

by:lruiz52
ID: 38794890
config
vlan (staff vlan #) untagged A1-A24
0
 
LVL 17

Expert Comment

by:jburgaard
ID: 38795994
On the Procurve2626  the ports are named 1,2,3 ... 25,26
show vlans   will show vlan-ID to vlan-name mapping
show vlan 8  fx will show tagging/untagging of ports in vlan 8

You do not mention where the uplink-port is, it could be tagged or untagged in the Vlan for staff.
Important is that the uplink-port-tagging for the "Vlan for staff" end up matching the tagging in the other end of the link.

HTH
0
 

Author Comment

by:armsteadw
ID: 38799251
I can see the two vlans i want to remove one and keep the other without any problems
when i try to remove the unwanted vlan i get a error stating that I cant remove vlan if its tagged or untagged.
what should it be before i remove it and what should the settings of the vlan that im keeping be?
0
 

Author Comment

by:armsteadw
ID: 38799931
96serverconfig.docxscreen shot
0
 
LVL 17

Accepted Solution

by:
jburgaard earned 500 total points
ID: 38801696
You should start with the wanted ports, then the unwanted could go away.

some rules:
A port can not be left without at least one vlan-setting (orfan)
A port can be tagged or untagged or none in a particular vlan, but not both tagged and untagged
A port can be tagged in multiple vlans, only untagged in one.

So if you have a working uplink to other switch on port 25 , let that be unchanged.
In vlan2 modify  2-24 as untagged.
now you can remove vlan 20 (now it is only tagged on port 25)
You communicate to the switch on 10.0.0.96,
 I F  that is in vlan 2 you could also get gid of vlan1 , but in order to do so, port 26 should first be set in vlan 2 .

HTH
0

Featured Post

Independent Software Vendors: We Want Your Opinion

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Getting hacked is no longer a matter or "if you get hacked" — the 2016 cyber threat landscape is now titled "when you get hacked." When it happens — will you be proactive, or reactive?
WARNING:   If you follow the instructions here, you will wipe out your VTP and VLAN configurations.  Make sure you have backed up your switch!!! I recently had some issues with a few low-end Cisco routers (RV325) and I opened a case with Cisco TA…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

617 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question