Solved

backtrack5 r3 dell d830 install wlan

Posted on 2013-01-22
13
780 Views
Last Modified: 2016-11-23
Hi,  i cant connect to internet my dell d830 using wifi

It see the access ports, but once i hit connect, the wifi refreshes and sees no networks

I have dual boot with win 7 and it works fine from there



regular lan works, but i need wifi

old question was here
http://www.experts-exchange.com/OS/Linux/Q_27961547.html
0
Comment
Question by:Ess Kay
  • 7
  • 6
13 Comments
 
LVL 13

Expert Comment

by:Alexios
ID: 38848424
Hello
Is your wireless adapter supported ?

give us the model and also a print out from the commands
iwconfig
ifconfig
0
 
LVL 15

Author Comment

by:Ess Kay
ID: 38868171
its a
RTL8188CU


the driver i found on

marked as RTL8188CUS


Im newish to linux, cant open the instruction because they are pdf and Dont have pdf viewer.

There is an install.sh file included, not sure how to run it
0
 
LVL 13

Expert Comment

by:Alexios
ID: 38868185
a print out from the commands
iwconfig
ifconfig
0
 
LVL 15

Author Comment

by:Ess Kay
ID: 38868307
Cant,  no internet,  lol
0
 
LVL 13

Expert Comment

by:Alexios
ID: 38868536
Come on...

You do not need internet
copy and paste it to a text file and access it from your win7
iwconfig.gif
0
 
LVL 15

Author Comment

by:Ess Kay
ID: 38868638
ok, ill do when i get home
0
Maximize Your Threat Intelligence Reporting

Reporting is one of the most important and least talked about aspects of a world-class threat intelligence program. Here’s how to do it right.

 
LVL 15

Author Comment

by:Ess Kay
ID: 38870533
iwconfig
ifconfig

root@bt:~# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:1c:23:9b:7d:00  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:26 errors:0 dropped:0 overruns:0 frame:0
          TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1769 (1.7 KB)  TX bytes:1769 (1.7 KB)


# iwconfig
lo        no wireless extensions.

wlan1     IEEE 802.11bgn  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm  
          Retry  long limit:7   RTS thr=2347 B   Fragment thr:off
          Encryption key:off
          Power Management:on
         
wlan0     IEEE 802.11bg  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=off  
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
         
eth0      no wireless extensions.
0
 
LVL 13

Accepted Solution

by:
Alexios earned 500 total points
ID: 38873751
Here I can see two wireless adapters

The one is switched off and the other is working
Is that correct?
You have two wireless adapters?

Now type this command and post the results
airmon-ng start wlan1
0
 
LVL 15

Author Comment

by:Ess Kay
ID: 38873818
one is the local adapter, doesnt work well(it see connections the when you click connect it sees nothing), the other is the dongle i am trying to install which works works well
0
 
LVL 13

Expert Comment

by:Alexios
ID: 38873827
ok nice
send the results of the command that I wrote before
0
 
LVL 15

Author Comment

by:Ess Kay
ID: 38873852
root@bt:~# airmon-ng start wlan1


Found 2 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID      Name
1510      dhclient3
1567      dhclient3
Process with PID 1510 (dhclient3) is running on interface wlan0


Interface      Chipset            Driver

wlan1            Unknown       rtl8192cu - [phy1]
                        (monitor mode enabled on mon0)
wlan0            Broadcom      b43 - [phy0]
0
 
LVL 13

Expert Comment

by:Alexios
ID: 38875187
Your card is working fine

Keep the other disabled and run wicd
Try to connect to your wireless network
Screenshot-1.png
0
 
LVL 13

Expert Comment

by:Alexios
ID: 38881311
Glad to help
0

Featured Post

How to run any project with ease

Manage projects of all sizes how you want. Great for personal to-do lists, project milestones, team priorities and launch plans.
- Combine task lists, docs, spreadsheets, and chat in one
- View and edit from mobile/offline
- Cut down on emails

Join & Write a Comment

Java performance on Solaris - Managing CPUs There are various resource controls in operating system which directly/indirectly influence the performance of application. one of the most important resource controls is "CPU".   In a multithreaded…
#Citrix #Citrix Netscaler #HTTP Compression #Load Balance
Learn how to navigate the file tree with the shell. Use pwd to print the current working directory: Use ls to list a directory's contents: Use cd to change to a new directory: Use wildcards instead of typing out long directory names: Use ../ to move…
In a previous video, we went over how to export a DynamoDB table into Amazon S3.  In this video, we show how to load the export from S3 into a DynamoDB table.

757 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

20 Experts available now in Live!

Get 1:1 Help Now