Solved

PIX or ASA by default configuration

Posted on 2013-05-09
5
334 Views
Last Modified: 2013-05-15
Hi, Anyone can give me suggestion? why PIX "show run policy-map" is nothing in GNS3 ?
What i saw in ASA is there are a lot command lines when using the show command. Please see attachment, Thanks
bydefault.JPG
0
Comment
Question by:EESky
  • 3
  • 2
5 Comments
 
LVL 4

Expert Comment

by:iammorrison
ID: 39154301
Usually because it depends on what IOS version you are using. The syntax has changed even very recently so if you are loading in an older IOS (especially since PIX is obsolete), some of the commands will not translate or carry over. Make sure you are labbing with a similar IOS release.
0
 

Author Comment

by:EESky
ID: 39154344
Thank you !
i guess you are right. i am using new version:


pixfirewall(config-if)# sh ver

Cisco PIX Security Appliance Software Version 8.0(2)

Compiled on Fri 15-Jun-07 18:25 by builders
System image file is "Unknown, monitor mode tftp booted image"
Config file at boot was "startup-config"

pixfirewall up 43 mins 4 secs

Hardware:   PIX-525, 256 MB RAM, CPU Pentium II 1 MHz
Flash E28F128J3 @ 0xfff00000, 16MB
BIOS Flash AM29F400B @ 0xfffd8000, 32KB

 0: Ext: Ethernet0           : address is 00aa.006a.e700, irq 9
 1: Ext: Ethernet1           : address is 00aa.006a.e701, irq 11
 2: Ext: Ethernet2           : address is 00aa.006a.e702, irq 11
 3: Ext: Ethernet3           : address is 0000.ab2a.8103, irq 11
 4: Ext: Ethernet4           : address is 0000.abb0.4704, irq 11

Licensed features for this platform:
Maximum Physical Interfaces  : 10
Maximum VLANs                : 100
Inside Hosts                 : Unlimited
Failover                     : Active/Active
VPN-DES                      : Enabled
VPN-3DES-AES                 : Enabled
Cut-through Proxy            : Enabled
Guards                       : Enabled
URL Filtering                : Enabled
Security Contexts            : 2
GTP/GPRS                     : Disabled
VPN Peers                    : Unlimited

This platform has an Unrestricted (UR) license.
0
 
LVL 4

Accepted Solution

by:
iammorrison earned 500 total points
ID: 39154382
No problem, hope it helps! :D
0
 

Author Comment

by:EESky
ID: 39154384
why ASA also show the same result as pix in GNS3 ?
0
 
LVL 4

Expert Comment

by:iammorrison
ID: 39154394
Im not sure, maybe it was labeled as ASA when its a PIX config, Ive seen it happen before
0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This article assumes you have at least one Cisco ASA or PIX configured with working internet and a non-dynamic, public, address on the outside interface. If you need instructions on how to enable your device for internet, or basic configuration info…
From Cisco ASA version 8.3, the Network Address Translation (NAT) configuration has been completely redesigned and it may be helpful to have the syntax configuration for both at a glance. You may as well want to read official Cisco published AS…
Both in life and business – not all partnerships are created equal. As the demand for cloud services increases, so do the number of self-proclaimed cloud partners. Asking the right questions up front in the partnership, will enable both parties …
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…

810 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question