Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

Force10 LLDP Configuration

Posted on 2013-05-29
6
Medium Priority
?
4,303 Views
Last Modified: 2013-06-03
I have been trying to setup LLDP on some of our Force10 switches. I am having an issue getting the information I want from it.


So far I have this configured:


protocol lldp
 no disable

interface TenGigabitEthernet 0/51
 description backup-S50V-Mpls
 no ip address
 switchport
!
 protocol lldp
 no shutdown

But when I type show lldp neighbors I am barely getting any information:
backup-S50V-StPaul#show lldp neighbor
 Loc PortID   Rem Host Name     Rem Port Id                Rem Chassis Id
 -------------------------------------------------------------------------

 Te 0/51      -                 TenGigabitEthernet 0/51    00:01:e8:d7:3f:18


How do I get the Hostname, remote ip(if there is one) and more detailed information to be transmitted between the two switches?

I've heard it has something to do with Advertise TLVs?


Also an example of how to configure this in Cisco IOS and JUNOS would also be much appreciated.
0
Comment
Question by:ThePorthos
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 3
6 Comments
 
LVL 2

Accepted Solution

by:
J30A4 earned 2000 total points
ID: 39209105
What version of FTOS are you running?

im running FTOS 8.4.2.6

protocol lldp
 advertise dot1-tlv port-protocol-vlan-id port-vlan-id
 advertise dot3-tlv max-frame-size
 advertise management-tlv system-capabilities system-description system-name
 advertise med
 hello 10
 no disable
 advertise interface-port-desc

make sure you do this on both ends

-Johnny
0
 

Author Comment

by:ThePorthos
ID: 39209626
I think its he same version, or 8.4.2.5, will check tomorrow. Is there a usual max frame size set for LLDP, I do remember seeing these commands available? I'm coming from Cisco CDP land so I'm not used to setting this different values. Could you show me a generic example of those data fields filled?
0
 
LVL 2

Expert Comment

by:J30A4
ID: 39211611
As far I know you can not change the frame size for lldp.

If you wan to see the device name all you should need is this

protocol lldp 
 advertise management-tlv system-description system-name 
no disable 

Open in new window


 
#show lldp neighbors
 Loc PortID   Rem Host Name     Rem Port Id                Rem Chassis Id     
 -------------------------------------------------------------------------
 
 Te 0/0       CA-VAN37-C30-01   TenGigabitEthernet 6/4     00:01:e8:65:e7:99  
 Te 0/1       CA-VAN37-C30-01   TenGigabitEthernet 6/5     00:01:e8:65:e7:99  

Open in new window


The only reason I added all the other stuff is if you want a more detailed output. for ex:

# show lldp neighbors detail

 Local Interface Te 0/0 has 1 neighbor 
  Total Frames Out: 605251 
  Total Frames In: 516297 
  Total Neighbor information Age outs: 0 
  Total Frames Discarded: 0 
  Total In Error Frames: 0 
  Total Unrecognized TLVs: 0 
  Total TLVs Discarded: 0 
  Next packet will be sent after 1 seconds
  The neighbors are given below:
  -----------------------------------------------------------------------
 
    Remote Chassis ID Subtype: Mac address (4)
    Remote Chassis ID:  00:01:e8:d6:81:b5
    Remote Port Subtype:  Interface name (5)
    Remote Port ID:  TenGigabitEthernet 0/49
    Local Port ID: TenGigabitEthernet 0/0
    Locally assigned remote Neighbor Index: 1
    Remote TTL:  40
    Information valid for next 36 seconds 
    Time since last information change of this neighbor:  8w3d23h
    Remote MTU:  1554
    Remote System Name:  CA-VAN37-S50-1ST-FLOOR-01
    Remote System Desc:  Dell Force10 Real Time Operating System Software. De
     ll Force10 Operating System Version: 1.0. Dell Force
     10 Application Software Version: 8.4.2.7. Copyright 
     (c) 1999-2012 Dell Inc. All Rights Reserved.Build Ti
     me: Thu Sep 27 14:03:07 PDT 2012
    Existing System Capabilities:  Repeater Bridge Router
    Enabled System Capabilities:  Repeater Bridge Router
    Port and Protocol Vlan ID: 4, Capability: Supported, Status: Enabled  
    Port and Protocol Vlan ID: 210, Capability: Supported, Status: Enabled  
    Port and Protocol Vlan ID: 211, Capability: Supported, Status: Enabled  
    Port and Protocol Vlan ID: 212, Capability: Supported, Status: Enabled  
    Port and Protocol Vlan ID: 300, Capability: Supported, Status: Enabled  
    Port and Protocol Vlan ID: 4093, Capability: Supported, Status: Enabled

Open in new window

0
Are You Ready for GDPR?

With the GDPR deadline set for May 25, 2018, many organizations are ill-prepared due to uncertainty about the criteria for compliance. According to a recent WatchGuard survey, a staggering 37% of respondents don't even know if their organization needs to comply with GDPR. Do you?

 

Author Comment

by:ThePorthos
ID: 39212975
I see, thanks. I will try it monday.
0
 

Author Closing Comment

by:ThePorthos
ID: 39216524
Worked great. Thank you sir.
0
 
LVL 2

Expert Comment

by:J30A4
ID: 39217417
no prob.
0

Featured Post

Hire Technology Freelancers with Gigs

Work with freelancers specializing in everything from database administration to programming, who have proven themselves as experts in their field. Hire the best, collaborate easily, pay securely, and get projects done right.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This article is in regards to the Cisco QSFP-4SFP10G-CU1M cables, which are designed to uplink/downlink 40GB ports to 10GB SFP ports. I recently experienced this and found very little configuration documentation on how these are supposed to be confi…
This article will show how Aten was able to supply easy management and control for Artear's video walls and wide range display configurations of their newsroom.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Get a first impression of how PRTG looks and learn how it works.   This video is a short introduction to PRTG, as an initial overview or as a quick start for new PRTG users.

704 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question