Solved

Roaming profile not being loaded

Posted on 2013-06-05
18
352 Views
Last Modified: 2013-06-24
Logging onto a domain with a Windows 7 Machine and keep getting the error that profile could not be loaded,

The machine has an IP address on the network and can ping the server etc

not sure where to start
0
Comment
Question by:pepps11976
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 9
  • 9
18 Comments
 

Author Comment

by:pepps11976
ID: 39222139
Its odd because even though I am logging in with domain\user

no folder is ever created under c:\users
0
 
LVL 14

Expert Comment

by:comfortjeanius
ID: 39222198
Do you see a C:\Users\TEMP folder?
0
Simplifying Server Workload Migrations

This use case outlines the migration challenges that organizations face and how the Acronis AnyData Engine supports physical-to-physical (P2P), physical-to-virtual (P2V), virtual to physical (V2P), and cross-virtual (V2V) migration scenarios to address these challenges.

 

Author Comment

by:pepps11976
ID: 39222330
No There is no Users\temp folder

if I go into user profile settings I can see there is a profile there of domain\user the size is 80 MB but I cannot see it anywhere
0
 
LVL 14

Expert Comment

by:comfortjeanius
ID: 39222496
What are you getting in the Application Logs in  event viewer, as far as the event ids?
0
 

Author Comment

by:pepps11976
ID: 39222536
Interestingly I am getting the following IDS

1129 Group Policy Failed
0
 
LVL 14

Expert Comment

by:comfortjeanius
ID: 39222545
0
 

Author Comment

by:pepps11976
ID: 39222631
Yep thanks but I had already found that document
0
 
LVL 14

Expert Comment

by:comfortjeanius
ID: 39222822
Perform actions and recheck the event logs and post back.
0
 

Author Comment

by:pepps11976
ID: 39223480
ok performed actions still getting the same Group Policy one

john
0
 
LVL 14

Expert Comment

by:comfortjeanius
ID: 39223497
That is the whole description  in the event log?


Did you check out this hotfix...

http://support.microsoft.com/kb/2459530
0
 

Author Comment

by:pepps11976
ID: 39223567
ok I have this one

Event ID 5719

This computer was not able to set up a secure session with a domain controller in domain ASPIREMEDICAL due to the following:
There are currently no logon servers available to service the logon request.
This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator.  

ADDITIONAL INFO
If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified domain.


And this 1129

The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has succesfully processed. If you do not see a success message for several hours, then contact your administrator.

will try hot fix now
0
 

Author Comment

by:pepps11976
ID: 39223656
No Change with the hot fix applied
0
 
LVL 14

Expert Comment

by:comfortjeanius
ID: 39223939
Check this link....

http://www.mysysadmintips.com/windows/active-directory/165-windows-7-machines-fail-to-apply-software-installation-group-policy-on-startup

Issue was fixed by enabling "Startup Policy Processing Wait Time" and setting wait time value to 10 seconds.
0
 

Author Comment

by:pepps11976
ID: 39224997
Ok I have unjoined from the domain and I am now trying to add the machine back onto the domain and getting the following message

Note: This information is intended for a network administrator.  If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt.

DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "ASPIREMEDICAL.local":

The query was for the SRV record for _ldap._tcp.dc._msdcs.ASPIREMEDICAL.local

The following domain controllers were identified by the query:
aspireserver.aspiremedical.local


However no domain controllers could be contacted.

Common causes of this error include:

- Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses.

- Domain controllers registered in DNS are not connected to the network or are not running.
0
 
LVL 14

Expert Comment

by:comfortjeanius
ID: 39225568
I received a message like that, try to reset the computer account or delete the account and re-add it, in active directory.

Plus try to do this from an elevated account

Start
Type cmd
right-click runas administrator
type ipconfig /flushdns
type ipconfig /registerdns

Then post back
0
 

Author Comment

by:pepps11976
ID: 39225674
Yep tried all of the following no luck
0
 
LVL 14

Accepted Solution

by:
comfortjeanius earned 500 total points
ID: 39225728
Did you try ipconfig /release  then /renew?


Look into this link right here...


http://geekswithblogs.net/technetbytes/archive/2011/10/09/147233.aspx
0

Featured Post

Free NetCrunch network monitor licenses!

Only on Experts-Exchange: Sign-up for a free-trial and we'll send you your permanent license!

Here is what you get: 30 Nodes | Unlimited Sensors | No Time Restrictions | Absolutely FREE!

Act now. This offer ends July 14, 2017.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

The recent Microsoft changes on update philosophy for Windows pre-10 and their impact on existing WSUS implementations.
The Windows functions GetTickCount and timeGetTime retrieve the number of milliseconds since the system was started. However, the value is stored in a DWORD, which means that it wraps around to zero every 49.7 days. This article shows how to solve t…
In this Micro Tutorial viewers will learn how to use Boot Corrector from Paragon Rescue Kit Free to identify and fix the boot problems of Windows 7/8/2012R2 etc. As an example is used Windows 2012R2 which lost its active partition flag (often happen…
The viewer will learn how to successfully create a multiboot device using the SARDU utility on Windows 7. Start the SARDU utility: Change the image directory to wherever you store your ISOs, this will prevent you from having 2 copies of an ISO wit…

688 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question