Solved

draytek cctv through firewall

Posted on 2013-06-07
5
785 Views
Last Modified: 2013-06-19
Ok guys

I am trying to get a cctv ports 82 and 9000 tcp/udp working I am getting on a open ports scanner

Host is up (0.11s latency).
PORT    STATE         SERVICE
400/tcp open          work-sol
401/tcp open          ups
400/udp open|filtered work-sol
401/udp open|filtered ups

my port redirects are 82-> 400
and 9000 to -> 401

but udp is open filtered which kind of says the firwall needs a rule for ports 82(400) and 9000(401)
am I correct in this assumption

as I need the cctv access to outside
0
Comment
Question by:IanTh
  • 3
  • 2
5 Comments
 
LVL 63

Expert Comment

by:btan
ID: 39231197
From its FAQ and "Open Port Setup"  article maybe that can help in Port Forwarding

http://www.draytek.co.uk/support/vfaq.html

How do I open the Firewall in my Vigor Router to allow access to computer / device on my network from the Internet?

Assuming the computer / device on your network has a Private (NAT'd) IP Address, you need to use the Open Ports Setup in the Vigor to allow access from the Internet. You do not need to use the IP Filter/Firewall Setup.

http://www.draytek.co.uk/support/kb_vigor_portforwarding.html
0
 
LVL 30

Author Comment

by:IanTh
ID: 39231618
But I thought on drayteks website instead on using open ports or redirects use cms as thats the new way ?
0
 
LVL 63

Expert Comment

by:btan
ID: 39231626
I am not a draytek user hence none the wiser but I see the qns as general exposing internal service to external. Better to clarify with support if you are a user
http://www.draytek.co.uk/support/
0
 
LVL 30

Accepted Solution

by:
IanTh earned 0 total points
ID: 39247201
ok I found out 400 is not good its used by virus's over udp so the firwall was filtering 400 so I found unused ports and choose those and it worked

so 82 for web and 9000 for media  open port

or 40 for web (port 40 unused) and 4 ( port 4 is unused) for media port redirect
0
 
LVL 30

Author Closing Comment

by:IanTh
ID: 39258755
I found out 400 and 401 where bad choices for udp as virus' use them as udp is stateless so the firewall was filtering if I choose a port like 4 that is not used by anything it works
0

Featured Post

Now Available: Firebox Cloud for AWS and FireboxV

Firebox Cloud brings the protection of WatchGuard’s leading Firebox UTM appliances to public cloud environments. It enables organizations to extend their security perimeter to protect business-critical assets in Amazon Web Services (AWS).

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Home network with two AP's dropping WiFi connectivity 12 87
ISP Change 14 70
parental control on huwei HG658b 1 29
Palo Alto site-to-site vpn monitoring 5 51
Hello , This is a short article on how would you go about enabling traceoptions on a Juniper router . Traceoptions are similar to Cisco debug commands but these traceoptions are implemented in Juniper networks router . The following demonstr…
Tired of waiting for your show or movie to load?  Are buffering issues a constant problem with your internet connection?  Check this article out to see if these simple adjustments are the solution for you.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

733 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question