Solved

Cisco 8005.   Need to open all ports

Posted on 2013-06-18
3
285 Views
Last Modified: 2013-06-22
Hi Experts.   I need to open all ports on a pair of old Cisco 8005 routers on a leased line.   Security is not a consideration in this particular instance.   Can someone advise me of the commands that would allow all traffic from both sides?   Many Thanks
0
Comment
Question by:PNRT
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 17

Accepted Solution

by:
surbabu140977 earned 500 total points
ID: 39256585
: )

If you do not put any restrictions, then all ports should be open (whatever you require).

Btw, ports does not work like a door that you open it. Applications open ports in device. e.g if you do not have http/ftp service in anything you cannot open port 80 or 21 yourself. That  application which will use port 80 or 21 will open it.

Do not worry about any ports in cisco routers. They should be available to you without doing anything. Still, if something does not work as expected help will be available here.

Please note you will be ONLY able to block (and subsequent selective allow) a port. You cannot open an unused/every port.

Best,
0
 
LVL 2

Author Comment

by:PNRT
ID: 39257436
Many thanks for this it is a great help  I have a situation where from one end of the leased line I can ping devices at the other end, but I cannot connect to anything.  When I do a port scan of a device it shows no ports open, but users at the other end have full functionality, port 25,  Port 80 etc   There are no firewalls involved and have checked everything else and figure it can only be the routers blocking in some way.  From what you say, I should be able to see any restrictions on the routers but I cant see anything obvious.  Even had the guys from Head Office take a look but nothing.   Many thanks for helping.
0
 
LVL 17

Expert Comment

by:surbabu140977
ID: 39258397
It's weird. But nothing uncommon. You can paste the config of the 2 routers here. We will take a look. (I believe nothing is in the routers).

Is it simple like LAN---->Router1----->WAN---->Router2----->LAN type scenario?

Best,
0

Featured Post

Manage your data center from practically anywhere

The KN8164V features HD resolution of 1920 x 1200, FIPS 140-2 with level 1 security standards and virtual media transmissions at twice the speed. Built for reliability, the KN series provides local console and remote over IP access, ensuring 24/7 availability to all servers.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Two IPV6 prefixes have same meaning under prefix-set in ASR9K? 2 47
Receiving wifi on an underground station 22 168
Router question 6 548
Unable to enable HWIC 2FE 2 26
This article is a guide to configure bridging on Cisco Routers.  This is something I never knew was possible until after making a few phone calls to Cisco.  Using bridging saved our company money by not requiring us to purchase a new switch.  Bridgi…
Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

732 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question