Solved

EPL circuit

Posted on 2013-06-29
9
436 Views
Last Modified: 2013-07-01
EPL circuit needs assistance to configuring the connection on my Cisco router. As per Cisco, my configuration is ok, but I don't see the other side of my router if I attach two laptop one to each side of the line, I can ping each side.

Cisco and Verizon seem to think I need crossover cable.

Any help will be truly appreciated.
0
Comment
Question by:joaquinbrito
  • 5
  • 4
9 Comments
 
LVL 28

Expert Comment

by:Jan Springer
ID: 39286851
Please do a

sh run int <whatever the interface is called>
sh int <whatever the interface is called>
0
 

Author Comment

by:joaquinbrito
ID: 39286980
interface FastEthernet0/1
no ip address
speed 100
full-duplex
!
interface FastEthernet0/1.1
encapsulation dot1Q 1 native
ip address 10.178.194.86 255.255.255.252
0
 

Author Comment

by:joaquinbrito
ID: 39286983
On router number 2 almost the same but different IP address.
0
PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

 
LVL 28

Expert Comment

by:Jan Springer
ID: 39287031
please "sho int f0/1" and "sho int f0/1.1"
0
 

Author Comment

by:joaquinbrito
ID: 39287256
Brooklyn_WAN_2#show interface FastEthernet0/1
FastEthernet0/1 is up, line protocol is up
  Hardware is Gt96k FE, address is 000f.8fce.1721 (bia 000f.8fce.1721)
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, 100BaseTX/FX
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     27787 packets output, 2272505 bytes, 0 underruns
     0 output errors, 0 collisions, 5 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
 
 
Brooklyn_WAN_2#show interface FastEthernet0/1.1
FastEthernet0/1.1 is up, line protocol is up
  Hardware is Gt96k FE, address is 000f.8fce.1721 (bia 000f.8fce.1721)
  Internet address is 10.178.194.86/30
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation 802.1Q Virtual LAN, Vlan ID  1.
  ARP type: ARPA, ARP Timeout 04:00:00
  Last clearing of "show interface" counters never
0
 
LVL 28

Expert Comment

by:Jan Springer
ID: 39288300
Can you ping yourself at 10.178.194.86 and can you ping the remote at 10.178.194.85?

I wouldn't think that you need a cross over cable but have you tried one?
0
 

Author Comment

by:joaquinbrito
ID: 39288606
I can ping myself but not the remote.  
However if I connect a laptop directly to the EPL jack of the local and another on the remote site, I can ping across the cable the laptops on each site.
0
 
LVL 28

Accepted Solution

by:
Jan Springer earned 500 total points
ID: 39289542
It's time to test with a crossover cable.
0
 

Author Closing Comment

by:joaquinbrito
ID: 39291235
Crossover cable did it thanks.
0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

It happens many times that access list (ACL) have to be applied to outgoing router interface in order to limit some traffic.This article is about how to test ACL from the router which is not very intuitive for everyone. Below scenario shows simple s…
This article is a guide to configure bridging on Cisco Routers.  This is something I never knew was possible until after making a few phone calls to Cisco.  Using bridging saved our company money by not requiring us to purchase a new switch.  Bridgi…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

773 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question