Craig-AK
asked on
Cisco 1841 router with a 4-port etherSwitch card- doesn't see the card
I have a Cisco 1841 Router that I need to add an additional routed network to use as a DMZ. I am trying to create a VLAN for the switch port and then use that VLAN as the 3rd network this router is directly connected to.
My problem, I have installed a 4-port Cisco EtherSwitch 10BASE-T/100BASE-TX autosensing HWIC (HWIC-4ESW) in Slot 0 on the router. I rebooted the router and as far as I can tell it does not see the card.
Below is the sh ver:
Office-1841#sh ver
Cisco IOS Software, 1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 25-Feb-09 15:45 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)
Office-1841 uptime is 18 hours, 53 minutes
System returned to ROM by power-on
System image file is "flash:c1841-advsecurityk9
This product contains cryptographic features and is subject to United
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 1841 (revision 5.0) with 356352K/36864K bytes of memory.
Processor board ID FTX0949X25D
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
122976K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Office-1841#
This device has a site-to-site VPN to another office and connects to the internet via a DSL modem - this is done on Dialer1 for the PPPOe. It acts as the firewall using the IOS firewall.
OUESTION:
Is there a command to run so the router will see the switch card?
or
Do I need a different version of IOS? if so which one that includes the VPN, firewall, Dialer interface, and the switch port card?
When this works how will the switch ports be numbered?
The 2 fixed Ethernet interfaces are numbered:
interface FastEthernet0/0 & interface FastEthernet0/1
Thanks
Craig
My problem, I have installed a 4-port Cisco EtherSwitch 10BASE-T/100BASE-TX autosensing HWIC (HWIC-4ESW) in Slot 0 on the router. I rebooted the router and as far as I can tell it does not see the card.
Below is the sh ver:
Office-1841#sh ver
Cisco IOS Software, 1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 25-Feb-09 15:45 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)
Office-1841 uptime is 18 hours, 53 minutes
System returned to ROM by power-on
System image file is "flash:c1841-advsecurityk9
This product contains cryptographic features and is subject to United
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 1841 (revision 5.0) with 356352K/36864K bytes of memory.
Processor board ID FTX0949X25D
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
122976K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Office-1841#
This device has a site-to-site VPN to another office and connects to the internet via a DSL modem - this is done on Dialer1 for the PPPOe. It acts as the firewall using the IOS firewall.
OUESTION:
Is there a command to run so the router will see the switch card?
or
Do I need a different version of IOS? if so which one that includes the VPN, firewall, Dialer interface, and the switch port card?
When this works how will the switch ports be numbered?
The 2 fixed Ethernet interfaces are numbered:
interface FastEthernet0/0 & interface FastEthernet0/1
Thanks
Craig
ASKER
I originally had it in slot 1, and it didn't show up, so I put it in slot 0. That's where it is now. Is there a "show" command that should show what is in each slot?
ASKER CERTIFIED SOLUTION
membership
Create a free account to see this answer
Signing up is free and takes 30 seconds. No credit card required.
ASKER
I think the card is bad
ASKER
I've requested that this question be closed as follows:
Accepted answer: 0 points for Craig-AK's comment #a39327290
for the following reason:
no other explaination
Accepted answer: 0 points for Craig-AK's comment #a39327290
for the following reason:
no other explaination
the user has come to the same conclusion as me, what sort outcome as he accepting, the part is faulty, after some investigation work was done.
ASKER
Please change the grade to A
the numbering should be fastethernet 1/0, 1/1 , 1/2, 1/3.
remove it from the module and try the other slot, the card doesnt need any configuration to come up, do a sh conf to see if the new ports are showing up.