Solved

Sonicwall routing for multiply wans

Posted on 2013-10-23
15
368 Views
Last Modified: 2013-11-02
I have the following interfaces

X0 Lan
X1 Wan
X7 Second WAN
X8 Second LAN

If i create under routing the following following

Source: X8 subset
Destination: Any
Service: any
Gateway: Secondary Default Gateway
Interface: X7
Metric: 20
Comment: second lan

Once i apply this, my wireless looses internet connections. What am i doing wrong?
0
Comment
Question by:miamitech305
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
15 Comments
 
LVL 20

Expert Comment

by:carlmd
ID: 39596620
What interface is the wireless connected to?

What are you trying to do?
0
 

Author Comment

by:miamitech305
ID: 39596855
I have two network.

Network 1 on interface X0 and network 2 on X7.

I need network 1 to use WAN on interface X1 and network 2 use WAN on interface X8.
0
 
LVL 20

Expert Comment

by:carlmd
ID: 39597114
All you really need to do is create a route that directs traffic from X1 to X8.

Go to Network -> Routing

then select Add

Source would be what you named the lan behind X1
Destination would be Any
Service would be Any
Gateway would be Secondary Default Gateway
Interface would be X8

That should do it.
0
Online Training Solution

Drastically shorten your training time with WalkMe's advanced online training solution that Guides your trainees to action. Forget about retraining and skyrocket knowledge retention rates.

 

Author Comment

by:miamitech305
ID: 39597174
I tried that and i didnt have internet access.
0
 
LVL 20

Expert Comment

by:carlmd
ID: 39597215
Are you sure you have it configured correctly.

The source must be the lan behind X1 and NOT the X1 interface.

Have you defined the Seconday Default Gateway to be the first hop (ISP router?) after the interface and NOT the X8 interface ip?
0
 

Author Comment

by:miamitech305
ID: 39597393
how do you define the seconday default gateway?
0
 
LVL 20

Expert Comment

by:carlmd
ID: 39597500
The secondary default gateway should have been auto added when the interface was defined.

This assumes you have a recent model Sonicwall with a recent version of SonicOS.
0
 

Author Comment

by:miamitech305
ID: 39597789
I am attaching screenshots of my setup.
interfaceScreenshot.jpg
route-policy.jpg
0
 
LVL 20

Expert Comment

by:carlmd
ID: 39597962
Does the Secondary Default Gateway point to an ip that is on the same subnet as the X7 ip?
0
 

Author Comment

by:miamitech305
ID: 39598026
no, if i placed the cursor over the secondary default gateway, a balloon pops up with 0.0.0.0
0
 
LVL 27

Expert Comment

by:skullnobrains
ID: 39599682
not sure this is related but you are using wrong subnet masks for X3 and X8

10.0.0.0/255.0.0.0 is meaningful
10.10.0.0/255.255.0.0 and quite a few others are ok but the one you are using is not

What interface is the wireless connected to?
can i see the routing table before you add the rule ?
can you confirm both WAN connections work properly ?
0
 
LVL 20

Expert Comment

by:carlmd
ID: 39599907
What model Sonicwall do you have and what is the version of SonicOS Enhanced. The definition and how the Secondary Default Gateway is created has changed at version 5.5.
0
 
LVL 28

Expert Comment

by:masnrock
ID: 39603062
Did you make sure your NAT rules were laid out properly? That is most likely the cause of your issues...
0
 

Accepted Solution

by:
miamitech305 earned 0 total points
ID: 39607500
I was able to figure it out.

i needed to use

the x7 default gateway and it worked.
0
 

Author Closing Comment

by:miamitech305
ID: 39618575
I figured it out my self
0

Featured Post

Salesforce Has Never Been Easier

Improve and reinforce salesforce training & adoption using WalkMe's digital adoption platform. Start saving on costly employee training by creating fast intuitive Walk-Thrus for Salesforce. Claim your Free Account Now

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Short answer to this question: there is no effective WiFi manager in iOS devices as seen in Windows WiFi or Macbook OSx WiFi management, but this article will try and provide some amicable solutions to better suite your needs.
When it comes to security, there are always trade-offs between security and convenience/ease of administration. This article examines some of the main pros and cons of using key authentication vs password authentication for hosting an SFTP server.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Internet Business Fax to Email Made Easy - With  eFax Corporate (http://www.enterprise.efax.com), you'll receive a dedicated online fax number, which is used the same way as a typical analog fax number. You'll receive secure faxes in your email, f…

739 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question