Solved

Connecting Cisco Router to another DSL modem-router

Posted on 2013-10-29
4
1,326 Views
Last Modified: 2013-10-29
I have two routers:

First one, connected to the DSL line directly, a huawei HG532ci, it gives me access to the internet correctly to any computer by simply connection an ethernet cable to any of its 4 ports (or wireless as well).

I have another cisco router (cisco WRT120N) i want to connect to the fist one, and connect another computer to this second router (i have my reasons to do this, and not connecting directl to the first one).

So i want the second router (cisco) to give access to the internet with its ports, just like the first one.

I connected the second router (cisco) to the first one, from a LAN2 port in the first router to the "internet" port in the second, that receives the signal, as you see in the picture below.

The first (huawei) router, settings are as follows: see picture huawei.jpg

And the cisco router settins are also in the next pictures.

Whan am i doing wrong? Cisco IP is 192.168.1.2, Huawei router IP is the same but .1, dhcp is enabled, etc... I have no i idea what setting should be whats causing the cisco router not givin internet access

I have also attached an IPconfig from the computer connected to the cisco router.

thank you!!
20131029-175502.jpg
huawei.JPG
cisco1.jpg
cisco1-options.jpg
cisco2.jpg
cisco3.jpg
cisco4.jpg
cisco5.jpg
cisco6.jpg
ipconfig.jpg
0
Comment
Question by:celtician
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
4 Comments
 
LVL 7

Accepted Solution

by:
SterlingMcClung earned 500 total points
ID: 39609361
It sounds like you just want to use the Cisco router as a switch to get more network ports.  If this is the case, then you will want to disable all DHCP services on the Cisco and connect the LAN ports of the two routers.  If you are trying to segment a section of your network behind the Cisco router, then you will need to choose separate IP ranges for the two networks, in order for the Cisco router to properly NAT.  If I am completely off on what you are trying to do, then you may want to provide a little more information as to why you are adding the cisco into the mix. Then we can figure out how it should be setup.
0
 

Author Comment

by:celtician
ID: 39609503
OH yes i forgot to say what i wanted to do, i just want as you said add more network ports to my network. Im trying your solution now.
0
 
LVL 7

Expert Comment

by:SterlingMcClung
ID: 39609563
Yeah, so in the cisco router, disable DHCP, the IP address that you have, (.2) should be fine.  If you want, make sure that the DNS and gateway are set to the other router (.1), then connect the other router lan2 to port 1 on the cisco and you should be off and running.  You won't be using any of the features of the Cisco router, but even using the wireless from the Cisco router will likely work as expected.  There is a chance that the wireless won't want to work properly, but I haven't seen that in a a Cisco/Linksys router in quite some time.
0
 

Author Comment

by:celtician
ID: 39610155
It worked, thank you!! i wasn't going to use the wireless so it doesnt matter if it works or not.
0

Featured Post

NFR key for Veeam Backup for Microsoft Office 365

Veeam is happy to provide a free NFR license (for 1 year, up to 10 users). This license allows for the non‑production use of Veeam Backup for Microsoft Office 365 in your home lab without any feature limitations.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
Getting hacked is no longer a matter or "if you get hacked" — the 2016 cyber threat landscape is now titled "when you get hacked." When it happens — will you be proactive, or reactive?
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…

710 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question