Solved

LACP Aggregation between two HP V1910-24G

Posted on 2013-11-08
7
4,844 Views
Last Modified: 2013-12-21
Hi Experts,

I would like to create a LACP aggregation with 4 interfaces between two HP V1910-24G switches.

I created a LACP aggregation on the 21 st to 24 th interfaces and disabled the unused 25 th to 28 th Mini Gbic ports on both switches.

I set the 21 to 24 ports access to trunk but I can't find how to assign a group for the LACP aggregation.

I can't ping hosts between the two switches, what did I do wrong or forget ?

I saw that we just have to activate LACP on desired ports with HP 2530 switch series to be OK.


Thank you for your help, best regards,
0
Comment
Question by:jet-info
  • 4
  • 2
7 Comments
 
LVL 50

Expert Comment

by:Don Johnston
ID: 39633230
The only thing that you should need to do is create the trunk.

i.e.: trunk 21-24 trk1 lacp
0
 
LVL 46

Expert Comment

by:Craig Beck
ID: 39633282
...and add that trunk to whichever VLANs you want it to carry...

vlan 10
 untagged 1-12,15-16
 tagged trk1
vlan 20
 untagged 13-14
 tagged trk1
vlan 30
 tagged trk1
0
 

Author Comment

by:jet-info
ID: 39633551
We use only one VLAN, do we need to do anything with trunk that in this case ?
0
Efficient way to get backups off site to Azure

This user guide provides instructions on how to deploy and configure both a StoneFly Scale Out NAS Enterprise Cloud Drive virtual machine and Veeam Cloud Connect in the Microsoft Azure Cloud.

 
LVL 46

Expert Comment

by:Craig Beck
ID: 39633557
If you're just using it as a flat switch, this should do it...

vlan 1
 untagged 1-24,trk1
0
 

Accepted Solution

by:
jet-info earned 0 total points
ID: 39634307
Hi,

So you tell me to set all ports to untagged and in trunk 1 ?

How can I do that command (trunk 21-24 trk1 lacp) through the GUI ?

We can't access in the configuration with the enable and conf t commands through CLI, we activated hidden  commands but there is still no enable command. (http://glazenbakje.wordpress.com/2012/08/21/hp-v1910-secret-commando-list-how-to-enable-it/)

We deleted aggregation, set the desired ports (21-24) as trunk link type and connected cables between the switches on these ports. We could ping both hosts (host A connected on switch A and B to B) one to another in both sides. We tested to put all the switch ports as trunk link type and it worked again, in fact it doesn't change anything (trink or not). We can ping hosts through the two switches (it works while 4 cables are connected between the two switches on ports 1-4 each side. When we create an aggregation ( static without LACP or dynamic with LACP) ping between the two hosts do not work anymore.

We get the error 3 on the LACP aggregation but we do not know what to change to fix it. We tried to set the priority of one interface in the LACP agg to 0 with no change.

What do we have to do to make that LACP aggregation working ?
0
 

Author Comment

by:jet-info
ID: 39723417
Thanks...
0
 

Author Closing Comment

by:jet-info
ID: 39733428
Thanks...
0

Featured Post

Free learning courses: Active Directory Deep Dive

Get a firm grasp on your IT environment when you learn Active Directory best practices with Veeam! Watch all, or choose any amount, of this three-part webinar series to improve your skills. From the basics to virtualization and backup, we got you covered.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

If you're not part of the solution, you're part of the problem.   Tips on how to secure IoT devices, even the dumbest ones, so they can't be used as part of a DDoS botnet.  Use PRTG Network Monitor as one of the building blocks, to detect unusual…
ADCs have gained traction within the last decade, largely due to increased demand for legacy load balancing appliances to handle more advanced application delivery requirements and improve application performance.
Viewers will learn how to connect to a wireless network using the network security key. They will also learn how to access the IP address and DNS server for connections that must be done manually. After setting up a router, find the network security…
Here's a very brief overview of the methods PRTG Network Monitor (https://www.paessler.com/prtg) offers for monitoring bandwidth, to help you decide which methods you´d like to investigate in more detail.  The methods are covered in more detail in o…

749 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question