Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

Cisco SRP527W to MikroTik GRE Tunnel

Posted on 2013-11-10
5
Medium Priority
?
1,117 Views
Last Modified: 2014-02-15
I'm trying to set up a GRE Tunnel from a Cisco SRP527W Router to a Mikrotik RouterBoard.
The Cisco end is head office, whereas the Mikrotik is at a remote site.
The Mikrotik sits behind the ADSL router at the office with all ports for VPN forwarded to it.

As the Cisco SRP has no CLI it's harder to set up than traditional methods.

Cisco:
Tunnel No: 1
Checksum: none
Sequence: None
Key: None
Wan interface: ADSL
Destination I.P: Remote Site WAN
Remote IP Address/Sbunet Mask: 172.20.10.1/29

Mikrotik:
Local address: 172.20.10.2/29
Remote Address: Head Office WAN I.P

The Mikrotik has the I.P address also assigned in the I.P > Addresses list and is assigned to the GRE tunnel interface.
On the Mikrotik I have created a NAT Masquerade rule to point the Head Office Subnet.

From the Mikrotik, pinging the 172.20.10.1 only shows a timeout...

Any ideas where I may have missed something???
0
Comment
Question by:kiwistag
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 4
5 Comments
 
LVL 3

Expert Comment

by:vyaradaikin
ID: 39722177
Is it still actual?
0
 
LVL 6

Author Comment

by:kiwistag
ID: 39722258
No luck as of yet...
0
 
LVL 6

Author Comment

by:kiwistag
ID: 39802587
The issue between sites is at one end the Netcomm NBPlus6Wn ADSL router is somehow blocking/interfering with the GRE tunnel. I am looking into why this may be as all NAT rules are in that should be..
0
 
LVL 6

Accepted Solution

by:
kiwistag earned 0 total points
ID: 39848518
After contacting Netcomm they suggested just switching the Router to Bridge Mode. Am yet to try but it seems like the only option.
0
 
LVL 6

Author Closing Comment

by:kiwistag
ID: 39861163
An option to resolve was offered by one of the routers manufacturers after they checked it with their engineers.
0

Featured Post

Manage your data center from practically anywhere

The KN8164V features HD resolution of 1920 x 1200, FIPS 140-2 with level 1 security standards and virtual media transmissions at twice the speed. Built for reliability, the KN series provides local console and remote over IP access, ensuring 24/7 availability to all servers.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
In this article, I am going to show you how to simulate a multi-site Lab environment on a single Hyper-V host. I use this method successfully in my own lab to simulate three fully routed global AD Sites on a Windows 10 Hyper-V host.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
This video gives you a great overview about bandwidth monitoring with SNMP and WMI with our network monitoring solution PRTG Network Monitor (https://www.paessler.com/prtg). If you're looking for how to monitor bandwidth using netflow or packet s…

670 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question