Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people, just like you, are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
Solved

Cisco point to point 4.5 mbs

Posted on 2013-11-21
12
259 Views
Last Modified: 2013-11-21
Hello.  We are having 3 t1 lines installed which will act as a point to point for my other office.  xo communications said they are installing hardware to bond the lines together and I will have one cable going to my router which is a cisco 1941 and I have a hwic t1 dsu csu.  I am not sure of the commands I will need since this is now not a regular t1 line that I am used to installing.  

My current config is below, but I imagine I need to do something different?

interface Serial0/0/0
 ip address 10.1.100.10 255.255.255.0
 service-module t1 clock source internal
 service-module t1 timeslots 1-24
0
Comment
Question by:bidgadget
  • 6
  • 6
12 Comments
 
LVL 12

Expert Comment

by:Infamus
ID: 39667195
can you do a "sh ip int brief"?

And also is it copper RJ-45 handoff?
0
 

Author Comment

by:bidgadget
ID: 39667214
it is a rj-45 handoff


DE_Phone_Router#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
Embedded-Service-Engine0/0 unassigned      YES NVRAM  administratively down down    
GigabitEthernet0/0         10.1.1.15       YES NVRAM  up                    up      
GigabitEthernet0/1         unassigned      YES NVRAM  administratively down down    
Serial0/0/0                10.1.100.10     YES NVRAM  up                    up      
Serial0/1/0                10.1.100.11     YES NVRAM  down                  down
0
 

Author Comment

by:bidgadget
ID: 39667218
the line is not connected as of yet to the router.  It  will go on s/0/1/0
0
PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

 
LVL 12

Accepted Solution

by:
Infamus earned 500 total points
ID: 39667261
It should be plugged into GigabitEthernet0/1

description P2P
 bandwidth 1000000
 ip address 10.1.100.10 255.255.255.0
  media-type rj45
end

Both router should be configured the same except the IP address.
0
 

Author Comment

by:bidgadget
ID: 39667267
they used a NetVanta by adtran to combine the lines
0
 

Author Comment

by:bidgadget
ID: 39667273
so I don't use the serial interface?
0
 
LVL 12

Expert Comment

by:Infamus
ID: 39667278
Hmmm...not sure about the NetVanta device.

Hopefully someone who's more knowledgeable can answer you then.

I was just thinking that it is point to point connection with copper handoff.

If it is normal point to point, it's mostly like connecting routers back to back.

I think your IPS (XO) should give you suggested config guides on the interconnecting interface.
0
 
LVL 12

Expert Comment

by:Infamus
ID: 39667280
Did it work?
0
 

Author Comment

by:bidgadget
ID: 39667284
thanks so much.  so to be clear.  I will not be using the serial interface at all for this?
0
 
LVL 12

Expert Comment

by:Infamus
ID: 39667285
Correct.
0
 

Author Comment

by:bidgadget
ID: 39667303
talked to xo.  it is the ethernet port.  Thanks again so much.
0
 
LVL 12

Expert Comment

by:Infamus
ID: 39667316
Glad I could help.

Good luck!!!
0

Featured Post

Portable, direct connect server access

The ATEN CV211 connects a laptop directly to any server allowing you instant access to perform data maintenance and local operations, for quick troubleshooting, updating, service and repair.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Cisco router recommendation for a 1 gig internet connection 11 72
HSRP needed? 4 56
Cisco Router help 5 71
How to Link NetGear wireless AC-1200 router to Sonicwall 3600 13 59
Tired of waiting for your show or movie to load?  Are buffering issues a constant problem with your internet connection?  Check this article out to see if these simple adjustments are the solution for you.
Getting hacked is no longer a matter or "if you get hacked" — the 2016 cyber threat landscape is now titled "when you get hacked." When it happens — will you be proactive, or reactive?
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

792 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question