Solved

DCDiag advertising test failing. SYSVOL and NETLOGON shares not replicating

Posted on 2013-11-27
9
2,617 Views
Last Modified: 2014-02-15
I've 2 site. HQ and Branch. There are 2 DCs in the HQ site. The primary server is on HQ. In the branch site also have 2 DCs.

I've just promoted a server to be branch site DC2. The DNS setting of the server is primary DNS point to itself and secondary DNS point to branch DC1.

I type net share and found sysvol and netlogon not shared. Run dcdiag and will get advertising test failed.

I also found the event log of File Replication service with error 13508.

I refer to this troubleshooting http://technet.microsoft.com/en-us/library/bb727056.aspx

But still gets error from dcdiag and sysvol and netlogon not shared.
0
Comment
Question by:sweehan
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 5
  • 3
9 Comments
 
LVL 23

Expert Comment

by:Thomas Grassi
ID: 39681374
What cddiag did you run?


@echo off
dcdiag >dclogx.txt
dcdiag /test:registerindns /dnsdomain:FQDN >>dclogx.txt
dcdiag /c /v >>dclogx.txt
dcdiag /test:dns >>dclogx.txt
exit


run this and post
0
 
LVL 16

Expert Comment

by:Dirk Mare
ID: 39682068
In dns management under server name and under domain name

Right click and go to properties
Go to name server tab

Make sure that all DNS servers are listed and that the correct IP is listed next to the correct server if you are not using ipv6 you can remove it from the list..
0
 

Author Comment

by:sweehan
ID: 39682563
File attached.
dclog1.txt
0
Optimizing Cloud Backup for Low Bandwidth

With cloud storage prices going down a growing number of SMBs start to use it for backup storage. Unfortunately, business data volume rarely fits the average Internet speed. This article provides an overview of main Internet speed challenges and reveals backup best practices.

 
LVL 23

Expert Comment

by:Thomas Grassi
ID: 39682660
After a quick review I see many errors it is late I will review in detail later

First glance DNS is a problem

Can you check your DNS a records and pointer records make sure the IP addresses are correct for each server make sure ipv6 is disabled on all network adapters and is not registering to DNS

Also each dc must have it self as the DNS server first entry must be the same IP address
0
 

Author Comment

by:sweehan
ID: 39682822
Checked the a records and pointer records. The ip addresses are correct. IPv6 has beeen disabled
0
 
LVL 23

Expert Comment

by:Thomas Grassi
ID: 39685224
can you ping by FQDN or only by ip address

ping JB-DC2.asis.edu.my what happens?

ping JB-DC3.asis.edu.my what happens?

etc.

You have 4 DC's correct try fro each one to ping each other by fqdn

also try from a computer on the network
0
 

Author Comment

by:sweehan
ID: 39691489
Hi,

ping from all the DC by FQDN. The ping returns the IP of the DCs are accurate.

I found that

EP-DC2 and JB-DC2 has error "DOMAIN SYSTEM VOLUME (SYSVOL SHARE)" is in JRNL_WRAP_ERROR" with event id 13568

EP-DC2 and JB-DC2 also has warning with event id 13562

EP-DC3 and JB-DC3 has warning with event id 13508
0
 

Accepted Solution

by:
sweehan earned 0 total points
ID: 39849406
I follow this resolution by microsoft http://support.microsoft.com/kb/290762

and the netlogon and sysvol are shared and replication are ok.
0
 

Author Closing Comment

by:sweehan
ID: 39861178
I've try this solution from this link and my new domain controller is able to work properly already.
0

Featured Post

Visualize your virtual and backup environments

Create well-organized and polished visualizations of your virtual and backup environments when planning VMware vSphere, Microsoft Hyper-V or Veeam deployments. It helps you to gain better visibility and valuable business insights.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Scenario:  You do full backups to a internal hard drive in either product (SBS or Server 2008).  All goes well for a very long time.  One day, backups begin to fail with a message that the disk is full.  Your disk contains many, many more backups th…
Sometimes drives fill up and we don't know why.  If you don't understand the best way to use the tools available, you may end up being stumped as to why your drive says it's not full when you have no space left!  Here's how you can find out...
This tutorial will give a an overview on how to deploy remote agents in Backup Exec 2012 to new servers. Click on the Backup Exec button in the upper left corner. From here, are global settings for the application such as connecting to a remote Back…
This tutorial will show how to configure a single USB drive with a separate folder for each day of the week. This will allow each of the backups to be kept separate preventing the previous day’s backup from being overwritten. The USB drive must be s…

705 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question