Solved

Active Directory

Posted on 2013-12-03
6
150 Views
Last Modified: 2013-12-04
I got two DC but they are not replicating each other, example. the user got locked out from his domain account and it is not showing in the other DC.  How do i fix this please? thanks
0
Comment
Question by:JessIT2013
  • 3
  • 3
6 Comments
 
LVL 35

Expert Comment

by:Mahesh
Comment Utility
Open cmd on both DCs and run below command and post the output here

repadmin /showrepl
dcdiag /q
ipconfig /all


So that we can troubleshoot further

Mahesh
0
 

Author Comment

by:JessIT2013
Comment Utility
Mahesh,

Please see attached as requested.
DC1.txt
DC2.txt
0
 
LVL 35

Expert Comment

by:Mahesh
Comment Utility
Ok
Logs showing that replication is happening properly and TCP/IP properties also correct

Please run below command on both DCs and check if sysvol and netlogon are there as shared folders and let me know.

Run below command on both DCs with cmd and post output here
repadmin /syncall

Also check in active directory sites and services if you can manually trigger the replication successfully ?
Check "Initiating Replication Using the Sites and Services Manager Snap-in" section in below article to trigger replication manually.
http://support.microsoft.com/kb/232072

Mahesh
0
Highfive Gives IT Their Time Back

Highfive is so simple that setting up every meeting room takes just minutes and every employee will be able to start or join a call from any room with ease. Never be called into a meeting just to get it started again. This is how video conferencing should work!

 

Author Comment

by:JessIT2013
Comment Utility
yes. it is replicating if I done it manually. how make it automatic? or is there any time to adjust? thanks
0
 
LVL 35

Accepted Solution

by:
Mahesh earned 500 total points
Comment Utility
So there you don't have to worry if manually triggered replication is working fine.

Intrasite Replication: (Replication between DCs in same site)
When a domain controller writes a change to its local copy of the Active Directory, a timer is started that determines when the domain controller's replication partners should be notified of the change. By default, this interval is 15 seconds in Windows Server 2003 and later.
You can use below article to change this interval, but its absolutely not required
http://support.microsoft.com/kb/214678

Inter site replication:
This replication schedule is 180 Mins by default within two sites.

Let me know your both DCs are in different locations and in different subnets ? so that I can help you.
If that's the case, have you created separate AD sites ?
You can create new AD site in that case, move your that location to that site.
Now your replication will be triggered every 180 Minutes

If you want to schedule replication with schedule task, then just create one batch file
with below syntax without Quotes and create schedule task on both servers at interval you want.
"repadmin /syncall"

Check below article how to create site
http://technet.microsoft.com/en-us/library/cc728152(v=ws.10).aspx

Mahesh
0
 

Author Closing Comment

by:JessIT2013
Comment Utility
Thanks Mahesh.
0

Featured Post

Threat Intelligence Starter Resources

Integrating threat intelligence can be challenging, and not all companies are ready. These resources can help you build awareness and prepare for defense.

Join & Write a Comment

Using in-flight Wi-Fi when you travel? Business travelers beware! In-flight Wi-Fi networks could rip the door right off your digital privacy portal. That’s no joke either, as it might also provide a convenient entrance for bad threat actors.
This paper addresses the security of Sennheiser DECT Contact Center and Office (CC&O) headsets. It describes the DECT security chain comprised of “Pairing”, “Per Call Authentication” and “Encryption”, which are all part of the standard DECT protocol.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

771 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

14 Experts available now in Live!

Get 1:1 Help Now