Solved

Local7.Warning xxx.xxx.xxx.xxx %CDP-W-NATIVE_VLAN_MISMATCH:

Posted on 2013-12-07
3
902 Views
Last Modified: 2013-12-23
I have two Cisco SG300-20 switches.
One is being used as a central LAN switch and one is being used as an internet switch (i.e. to connect devices with public addresses).

I want to be able to access the internet switch for switch management from inside the LAN.
The public addressed devices are on VLAN1.
So, I've set up VLAN 2 and assigned one port to that VLAN.
Then, I've assigned a LAN IP address to the switch and can access it via this port/VLAN2.

This VLAN2 port on the internet switch connects to port ge10 on the LAN switch (which is operating everything on VLAN1 for *that* switch).  There are no trunks or tagging.

I'm getting messages:

Local7.Warning xxx.xxx.xxx.xxx %CDP-W-NATIVE_VLAN_MISMATCH:
Native VLAN mismatch detected on interface gi10.

I have tried to supress these messages using the command line interface to the switches but the commands I found and tried seem to not be available on these switches.

Is there a way to shut this warning off?  
What if I put everything on the LAN switch on *its* VLAN2?  Would that help?
0
Comment
Question by:Fred Marshall
  • 2
3 Comments
 
LVL 50

Expert Comment

by:Don Johnston
ID: 39703725
Is there a way to shut this warning off?  
Yes. Resolve the VLAN mismatch and the warnings will stop.  Or you can disable logging or disable CDP. But fixing the VLAN mismatch is the "right" way to fix it.

What if I put everything on the LAN switch on *its* VLAN2?  Would that help?
I think that will fix your problem.  It sounds like the port on the internet switch that your LAN switch is connected to is in VLAN 2. So if you change the g10 port on the LAN switch to VLAN 2, that will eliminate the VLAN mismatch.
0
 
LVL 25

Author Comment

by:Fred Marshall
ID: 39704726
Well, I've never done it that way before - so I could use a little more coaching.  If I switch the g10 port switch to a new VLAN2 on the LAN switch then how will that port communicate onto VLAN1 where everything else (including my workstation) is located?
0
 
LVL 50

Accepted Solution

by:
Don Johnston earned 500 total points
ID: 39704732
You would need to configure all the ports that are currently members of VLAN 1 to be members of VLAN 2.
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
md5 password 3 62
Internet Protocol Security question 3 71
QoS for Voip 7 39
Unmanaged Switches for Optimized Network Speeds 7 39
Short answer to this question: there is no effective WiFi manager in iOS devices as seen in Windows WiFi or Macbook OSx WiFi management, but this article will try and provide some amicable solutions to better suite your needs.
Meet the world's only “Transparent Cloud™” from Superb Internet Corporation. Now, you can experience firsthand a cloud platform that consistently outperforms Amazon Web Services (AWS), IBM’s Softlayer, and Microsoft’s Azure when it comes to CPU and …
Viewers will learn how to connect to a wireless network using the network security key. They will also learn how to access the IP address and DNS server for connections that must be done manually. After setting up a router, find the network security…
This video gives you a great overview about bandwidth monitoring with SNMP and WMI with our network monitoring solution PRTG Network Monitor (https://www.paessler.com/prtg). If you're looking for how to monitor bandwidth using netflow or packet s…

772 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question