Solved

Microsoft dynamics CRM adaptor

Posted on 2013-12-09
7
485 Views
Last Modified: 2013-12-11
The attached document has 2 screenshots of the connector i have installed.

The 1st one is the Ms Dynamics Crm

The 2nd is the MS Dynamics CRM2011



Is there a reason to why there are 2 crm's listed, or are these due to 2 diff versions
Connector.docx
0
Comment
Question by:Moizsaif123
  • 4
  • 3
7 Comments
 
LVL 29

Expert Comment

by:feridun
ID: 39705792
Yes, the Microsoft Dynamics CRM entry is for version 4.0.
0
 
LVL 4

Author Comment

by:Moizsaif123
ID: 39705823
Thanks for the quick response.

Bear with me if you check out the screenshot I have posted, this might be for an older version of connector which does not have
the CRM 2011 settings tab and this connector works during daily syncs

Is there a reason to why they have 2 versions involved for connectivity here...
0
 
LVL 4

Author Comment

by:Moizsaif123
ID: 39705824
attachement below,Sorry if I am being ambiguous, I just wanted to know why there are 2 versions being usd..
config4-adapoterSettings.jpg
0
IT, Stop Being Called Into Every Meeting

Highfive is so simple that setting up every meeting room takes just minutes and every employee will be able to start or join a call from any room with ease. Never be called into a meeting just to get it started again. This is how video conferencing should work!

 
LVL 4

Author Comment

by:Moizsaif123
ID: 39705888
Does this depend on the organization if that org were upgraded to 2011 the "2011 adaptor" would then work for them...please note article in one of the connector guides...



Adapters
Adapters are used to connect the runtime and the client to the Microsoft Dynamics CRM and Microsoft
Dynamics ERP web services. This connection is used for reading and writing data from one application
to another application.
The following adapters are available:
¿ Microsoft Dynamics CRM adapter – Connects with Microsoft Dynamics CRM 4.0 on-premises
only. This adapter is also compatible with Microsoft Dynamics CRM 2011 organizations that were
upgraded from Microsoft Dynamics CRM 4.0 and were previously integrated using Connector for
Microsoft Dynamics.
¿ Microsoft Dynamics CRM 2011 adapter – Connects with Microsoft Dynamics CRM 2011 only.
Use this adapter if you are integrating with Microsoft Dynamics CRM 2011 for the first time.
¿ Microsoft Dynamics ERP adapter – Connects with the Microsoft Dynamics ERP database.
Depending on your ERP system, Connector for Microsoft Dynamics might have more than version of
this adapter. For more information, see the Connector for Microsoft Dynamics ERP configuration
guide for your ERP system.
0
 
LVL 29

Accepted Solution

by:
feridun earned 500 total points
ID: 39708027
That could be the reason, if the organization started with CRM 4 and then upgraded to CRM 2011.

But if you only have one integration I would expect to see only one adapter configured for CRM and one for NAV.

Perhaps someone installed the CRM 2011 adapter and didn't use it.
0
 
LVL 4

Author Comment

by:Moizsaif123
ID: 39710577
I am connecting to a online CRM where when I check the version# it says 6.0.0.18 as shown in the attached screenshot. Is this the 2013 one..or still the 2011 ver
OnlineCrm.docx
0
 
LVL 29

Expert Comment

by:feridun
ID: 39710649
CRM versions starting with 6. are CRM 2013.

I don't know if the CRM 2011 adapter works with CRM 2013.
0

Featured Post

Enabling OSINT in Activity Based Intelligence

Activity based intelligence (ABI) requires access to all available sources of data. Recorded Future allows analysts to observe structured data on the open, deep, and dark web.

Join & Write a Comment

Sometimes in DotNetNuke module development you want to swap controls within the same module definition.  In doing this DNN (somewhat annoyingly) swaps the Skin and Container definitions to the default admin selections.  To get around this you need t…
In .NET 2.0, Microsoft introduced the Web Site.  This was the default way to create a web Project in Visual Studio 2005.  In Visual Studio 2008, the Web Application has been restored as the default web Project in Visual Studio/.NET 3.x The Web Si…
Excel styles will make formatting consistent and let you apply and change formatting faster. In this tutorial, you'll learn how to use Excel's built-in styles, how to modify styles, and how to create your own. You'll also learn how to use your custo…
Illustrator's Shape Builder tool will let you combine shapes visually and interactively. This video shows the Mac version, but the tool works the same way in Windows. To follow along with this video, you can draw your own shapes or download the file…

743 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

15 Experts available now in Live!

Get 1:1 Help Now