Solved

Basic multicast routing configuration

Posted on 2013-12-10
4
487 Views
Last Modified: 2013-12-25
Hi,

How to configure multicast routing for sending multicast packets from one vlan to
other vlan group

scenario :


cisco 3560 switch
   /               \
VLAN10       VLAN20

Source multicast traffic is from VLAN10

destination multicast is to VLAN 20 (few systems)


what is basic configuration at switch to meet the requirement

Regards
Ramu
0
Comment
Question by:RAMU CH
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
4 Comments
 
LVL 7

Accepted Solution

by:
unfragmented earned 500 total points
ID: 39710444
Enable multicast at the global config level:-
ip multicast-routing
(Some platforms need ip multicast-routing distributed instead)

Enable multicast routing at the interface config level:-
int vlan 10
 ip pim sparse-mode
int vlan 20
 ip pim sparse-mode

If you need to route multicast across multiple devices its a little more complex and needs a bit more config.

To validate and test, the following commands are helpful.
show ip mroute
show ip igmp groups
0
 
LVL 1

Author Comment

by:RAMU CH
ID: 39713229
Hi,

I have cofigured multicast ipaddress as 224.0.1.40 then it is working but
with 224.0.1.116 multicast ip address,it is not working

is there any difference in 224.0.1.40 ip address

Regards
Ramu
0
 
LVL 7

Assisted Solution

by:unfragmented
unfragmented earned 500 total points
ID: 39714035
For multicast to work properly, you need multicast aware applications.  For general application use, you should generally use an address from the 239.255.0.0/16 range, as these are defined in RFC's as being "administratively scoped".  

FYI, 224.0.1.40 is registered by Cisco as a well known mcast address for RP discovery.  224.0.1.116 is registered by Spectralink as a well known mcast address, i think for voice communications.
0
 
LVL 1

Author Closing Comment

by:RAMU CH
ID: 39739006
thanks
0

Featured Post

On Demand Webinar: Networking for the Cloud Era

Ready to improve network connectivity? Watch this webinar to learn how SD-WANs and a one-click instant connect tool can boost provisions, deployment, and management of your cloud connection.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

The worst thing when starting a new job is when the previous Network Administrator left behind no documentation. How do you get into the devices? If you've been in this situation or just accidently mistyped your password, this article will hopefully…
I eventually solved a perplexing problem setting up telnet for a new switch.  I installed a new Cisco WS-03560X-24P switch connected to an existing Cisco 4506 running a WS-X4013-10GE Sup II-Plus. After configuring vlans and trunking,  I could no…
This is a high-level webinar that covers the history of enterprise open source database use. It addresses both the advantages companies see in using open source database technologies, as well as the fears and reservations they might have. In this…
In this video we outline the Physical Segments view of NetCrunch network monitor. By following this brief how-to video, you will be able to learn how NetCrunch visualizes your network, how granular is the information collected, as well as where to f…

688 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question