Solved

Veeam Proxy Error

Posted on 2014-01-16
8
2,970 Views
Last Modified: 2014-01-21
When trying to add one server as a Backup Proxy in Veeam (fully patched version 7) I am getting the error:

[ServerName] Failed to install deployment service.
The specified server cannot perform the requested operation.

--tr.Failed to create persistent connection to ADMIN$ shared folder on host [ip address].
--tr:Failed to install service [VeeamDeploymentService] was not installed on the host [ip address].

In looking this up, I tried a few things that did not fix it.

I disabled UAC completely on the server
I did the registry change
Made sure proper ports were open

I can browse from my computer at the local site to \\server\admin$ just fine and have full read/write capabilities with the account I am using to authenticate during the install.

All of my other servers worked fine, the only difference being they are all Server 2008 R2, and this is Server 2012 Datacenter.

I'm going to look back through the remote firewalls logs to see if I can see anything, but wanted to get this out there in case someone experience the same and could shed some light on the situation.
0
Comment
Question by:DerekFG
  • 5
  • 3
8 Comments
 
LVL 119
ID: 39786783
Do you have Local Administrator or Domain Administrator priveleges on the Server?

can you connect to \\servername without any issues?
0
 
LVL 2

Author Comment

by:DerekFG
ID: 39786796
Yes, I can connect fine to the server and to the admin$ directory with full permission.  This is a domain controller as well, as the others are.  The only difference is that it is Server 2012.

Same firewalls at all sites, same config mainly.  9 sites work, this is the only that does not.
0
 
LVL 119
ID: 39786826
You do not have any Group Polcies in effect for this server?
0
Simplifying Server Workload Migrations

This use case outlines the migration challenges that organizations face and how the Acronis AnyData Engine supports physical-to-physical (P2P), physical-to-virtual (P2V), virtual to physical (V2P), and cross-virtual (V2V) migration scenarios to address these challenges.

 
LVL 2

Author Comment

by:DerekFG
ID: 39786872
Only the same that are domain wide.
0
 
LVL 119
ID: 39786907
One to fire at Veeam Support.
0
 
LVL 2

Author Comment

by:DerekFG
ID: 39787111
Posted the Log snippet from the Veeam Server.

Interesting enough, I can see in event viewer on the server that is failing to install that it successfully logging in and gaining full permission.

Server name and domain have been changed from log.
error.txt
0
 
LVL 2

Accepted Solution

by:
DerekFG earned 0 total points
ID: 39787622
Fixed it myself, issue was not being able to access the admin$ or any shares between only Server 2012 servers.

I created a reg DWORD HKLM\SYSTEM\CurrentControlSet\Services\LanmanWorkstation\Parameters\RequireSecureNegotiate and set the value to 2 on all of my Server 2012 VM's.

This has resolved the issue.
0
 
LVL 2

Author Closing Comment

by:DerekFG
ID: 39796496
Solution found myself.
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

In this article, I will show you HOW TO: Suppress Configuration Issues and Warnings Alert displayed in Summary status for ESXi 6.5 after enabling SSH or ESXi Shell.
In this article, I show you step by step with screenshots to assist you - HOW TO: Deploy and Install the VMware vCenter Server Appliance 6.5 (VCSA 6.5), with some helpful tips along the way.
To efficiently enable the rotation of USB drives for backups, storage pools need to be created. This way no matter which USB drive is installed, the backups will successfully write without any administrative intervention. Multiple USB devices need t…
This tutorial will walk an individual through the process of configuring their Windows Server 2012 domain controller to synchronize its time with a trusted, external resource. Use Google, Bing, or other preferred search engine to locate trusted NTP …

821 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question