Solved

Netgear VLAN questions

Posted on 2014-01-27
4
540 Views
Last Modified: 2014-02-09
I am configuring a VLAN using Netgear switches with SFP ports.  I have 6 separate buildings with there own network rack and each have a 48 port switch with a fiber run back to the main network room.  In the main network room, I have a 12 port SFP Netgear fiber switch and 2 48 port Netgear switches.  I also have 4 access points in each of the 6 buildings connected to port 1-4.  The fiber ports are port 49 in each of the buildings.  Here's what I did to configure the VLAN, please let me know if I may be missing anything.  I created the 2 VLAN's on every device, I left VLAN 1 as the management VLAN and made VLAN 11 for the private network, and VLAN 12 as the public network.  I tagged VLAN 11 and 12 on ports 1-4 and port 49 on all switches.  I also marked ports 5-24 untagged for VLAN 12 and 25-48 for VLAN 11. Then I went to routing and went to VLAN.  I selected the VLAN ID, entered the IP address and the subnet of what I wanted the switch to be set as for each VLAN.  <--Not sure if this is correct.
0
Comment
Question by:seanrhudy
  • 2
  • 2
4 Comments
 
LVL 26

Expert Comment

by:Soulja
ID: 39815417
Okay, I would take all of the vlans on the trunk ports leading back the to SFP switch. I would tag all the vlans connected to the AP's if you are running multiple ssid's per vlan on them. Each building switch would have an ip for VLAN 1 for management. The SFP switch would have an ip for all vlan's since it is routing for them.
0
 

Author Comment

by:seanrhudy
ID: 39816175
How would I give the SFP switch an IP for all VLAN's?  What would that be called?
0
 
LVL 26

Accepted Solution

by:
Soulja earned 395 total points
ID: 39816704
If the SFP switch is a layer 3 switch you would create a vlan interface for each vlan and assign an ip address to each. The ip you assign each vlan interface is the will be the default gateway for that vlan.
0
 

Author Comment

by:seanrhudy
ID: 39816835
It's a Netgear ProSafe GSM7212P
It says it provides comprehensive Layer 2, Lite Layer 3 and Layer 4 switching..should I be ok with that?  I also have a Sonicwall NSA 250 as the firewall.
0

Featured Post

Networking for the Cloud Era

Join Microsoft and Riverbed for a discussion and demonstration of enhancements to SteelConnect:
-One-click orchestration and cloud connectivity in Azure environments
-Tight integration of SD-WAN and WAN optimization capabilities
-Scalability and resiliency equal to a data center

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Expanding Subnet Mask 20 152
2 routers and 1 public IP Address. 10 55
creating SVI on layer 3 switch 1 23
VLAN Configuration on Cisco Switch 8 21
In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
The Cisco RV042 router is a popular small network interfacing device that is often used as an internet gateway. Network administrators need to get at the management interface to make settings, change passwords, etc. This access is generally done usi…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

860 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question