Solved

Cisco VPN not passing traffic

Posted on 2014-02-07
11
698 Views
Last Modified: 2014-02-08
I am working on a site that has a cisco asa 5505 in the main office with a vpns to it.  They just opened a new remote location and put in a cisco asa 5505 there.  I used the easy vpn wizard at the main site to setup a connection and configured the easy vpn at the remote site.  The vpn is showing that it is connected but no traffic is passing through.  I can see connection active and authentication takes place and they both look normal but that is it.  

Any help would be great.  Let me know if you need further detail
0
Comment
Question by:cnesupport
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 6
  • 5
11 Comments
 
LVL 95

Expert Comment

by:John Hurst
ID: 39841699
Are the subnets on each end different? They need to be.

Other than that, enable logging on both end, make the connection, and then what is in the logs about traffic.

You may need to enable NAT Traversal, but normally that affects the connection as well.

.... Thinkpads_User
0
 

Author Comment

by:cnesupport
ID: 39841701
yes both on are different subnets.  I have logging on but I don't see it blocking any traffic.  I am trying to find any denies.  I am assuming there are some rules I would need to put in the firewall for it but I am not sure what that would be.
0
 
LVL 95

Expert Comment

by:John Hurst
ID: 39841714
I use Juniper boxes for most clients, and there is a specific policy to permit VPN traffic both ways. I don't know what the counterpart is on a commercial Cisco box.

... Thinkpads_User
0
Microsoft Certification Exam 74-409

Veeam® is happy to provide the Microsoft community with a study guide prepared by MVP and MCT, Orin Thomas. This guide will take you through each of the exam objectives, helping you to prepare for and pass the examination.

 

Author Comment

by:cnesupport
ID: 39842581
got the vpn passing traffic by putting in some firewall rules.  Now the remote location can get to the main site but cannot get out to the internet!
0
 
LVL 95

Accepted Solution

by:
John Hurst earned 500 total points
ID: 39842604
I set a remote site Juniper so that the remote site uses internet via its own connection (not the home site internet). I don't think you should try to route remote internet through the home site as it will be slow.

Can you implement "split tunneling" at the remote site? That will let it use its own internet.

.... Thinkpads_User
0
 

Author Comment

by:cnesupport
ID: 39842611
I am not sure if the easy vpn allows it I will have to look.
0
 

Author Comment

by:cnesupport
ID: 39842623
ok I am setting up the split tunneling it is asking me to set some stuff as exempt

should I do the remote network?
0
 
LVL 95

Expert Comment

by:John Hurst
ID: 39842641
I am not exactly certain (because I employ Juniper instead) but I would think yes. Each end wants its own internet. I assume you are using IPsec.

... Thinkpads_User
0
 

Author Comment

by:cnesupport
ID: 39843526
split tunneling is the answer I just can't figure out how to configure it, Cisco is not my friend today.
0
 
LVL 95

Expert Comment

by:John Hurst
ID: 39843531
There is a Cisco Support article for Split Tunneling in Easy VPN.

http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080809222.shtml

It is a few lines down from the beginning of the configuration example.  I don't know if this applies to you as I am not a Cisco expert at all.

.... Thinkpads_User
0
 
LVL 95

Expert Comment

by:John Hurst
ID: 39844691
@cnesupport - Thanks and I was happy to help.
0

Featured Post

Free Tool: ZipGrep

ZipGrep is a utility that can list and search zip (.war, .ear, .jar, etc) archives for text patterns, without the need to extract the archive's contents.

One of a set of tools we're offering as a way to say thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

This is about downgrading PIX Version 8.0(4) & ASDM 6.1(5) to PIX 7.2(4) and ASDM 5.2(4) but with only 64MB RAM and 16MB flash. Background: You have a Cisco Pix 515E which was running on PIX 7.2(4) and its supporting ASDM 5.2(4) without any i…
I recently updated from an old PIX platform to the new ASA platform.  While upgrading, I was tremendously confused about how the VPN and AnyConnect licensing works.  It turns out that the ASA has 3 different VPN licensing schemes. "site-to-site" …
Both in life and business – not all partnerships are created equal. As the demand for cloud services increases, so do the number of self-proclaimed cloud partners. Asking the right questions up front in the partnership, will enable both parties …
Both in life and business – not all partnerships are created equal. Spend 30 short minutes with us to learn:   • Key questions to ask when considering a partnership to accelerate your business into the cloud • Pitfalls and mistakes other partners…

734 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question