Solved

error 13509 and 13508

Posted on 2014-02-07
8
279 Views
Last Modified: 2014-02-07
Hi,

There is 13509 on our main DC and 13508 on the backup DC.  When I used net share on both, backup dc shows netlogon and sysvol, but not on the main dc.

Is this normal?  Is there a step to correct this?  thx
0
Comment
Question by:mcrmg
  • 5
  • 3
8 Comments
 

Author Comment

by:mcrmg
ID: 39842049
I used dcdiag on the main dc, NetLogon is not there, how should I rebuild it?  thanks
0
 

Author Comment

by:mcrmg
ID: 39842134
here is what I have so far after following the steps, I have even 13566 but did not get a  13516, according to the steps, there is something else in FRS, not sure what direction I should take.  Thx




To complete an authoritative restore, stop the FRS service, configure the BurFlags registry key, and then restart the FRS service. To do so:

Click Start, and then click Run.
In the Open box, type cmd and then press ENTER.
In the Command box, type net stop ntfrs.
Click Start, and then click Run.
In the Open box, type regedit and then press ENTER.
Locate the following subkey in the registry:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\NtFrs\Parameters\Backup/Restore\Process at Startup
In the right pane, double click BurFlags.
In the Edit DWORD Value dialog box, type D4 and then click OK.
Quit Registry Editor, and then switch to the Command box.
In the Command box, type net start ntfrs.
Quit the Command box.
When the FRS service is restarted, the following actions occur:

The value for the BurFlags registry key is set back to 0.
An event 13566 is logged to signal that an authoritative restore is started.
Files in the reinitialized FRS replicated directories remain unchanged and become authoritative on direct replication. Additionally, the files become indirect replication partners through transitive replication.
The FRS database is rebuilt based on current file inventory.
When the process is complete, an event 13516 is logged to signal that FRS is operational. If the event is not logged, there is a problem with the FRS configuration.
0
 
LVL 59

Accepted Solution

by:
Kevin Cross earned 500 total points
ID: 39842141
These should replicate from other directory servers, so you can try the solutions in the following KB article to see if it helps.

Using the BurFlags registry key to reinitialize File Replication Service replica sets
http://support.microsoft.com/kb/290762

EDIT: I did not see your last post, so I appreciate your understanding if I repeated what you just did/said.
0
Best Practices: Disaster Recovery Testing

Besides backup, any IT division should have a disaster recovery plan. You will find a few tips below relating to the development of such a plan and to what issues one should pay special attention in the course of backup planning.

 

Author Comment

by:mcrmg
ID: 39842225
after following the steps, still getting error when using "dcdiag" on NETLOGON and SCRIPTS

net share is still not picking that up.....any ideas?  thx
0
 
LVL 59

Expert Comment

by:Kevin Cross
ID: 39842257
Do you have a firewall on either system?
0
 

Author Comment

by:mcrmg
ID: 39842262
that was the first thing I checked  (the easy one lol), no, both servers' fw are off..thanks
0
 
LVL 59

Expert Comment

by:Kevin Cross
ID: 39842263
You also can look at http://technet.microsoft.com/en-us/library/bb727056.aspx#EMAA, which  uses ntfrsutl.
0
 

Author Comment

by:mcrmg
ID: 39842639
thank you
0

Featured Post

VMware Disaster Recovery and Data Protection

In this expert guide, you’ll learn about the components of a Modern Data Center. You will use cases for the value-added capabilities of Veeam®, including combining backup and replication for VMware disaster recovery and using replication for data center migration.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Occasionally there is a need to clean table columns, especially if you have inherited legacy data. There are obviously many ways to accomplish that, including elaborate UPDATE queries with anywhere from one to numerous REPLACE functions (even within…
In this article I will describe the Backup & Restore method as one possible migration process and I will add the extra tasks needed for an upgrade when and where is applied so it will cover all.
This Micro Tutorial will give you a basic overview how to record your screen with Microsoft Expression Encoder. This program is still free and open for the public to download. This will be demonstrated using Microsoft Expression Encoder 4.
Along with being a a promotional video for my three-day Annielytics Dashboard Seminor, this Micro Tutorial is an intro to Google Analytics API data.

803 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question