?
Solved

LSI 9460 OID for optimal status and chip temp

Posted on 2014-02-17
4
Medium Priority
?
395 Views
Last Modified: 2014-02-18
I am trying to setup monitoring for LSI raid cards. I would like help on figuring out which OID has the VD status, Chip Temp, and Alarm status.

I have the OID for BBU temp

.1.3.6.1.4.1.3582.4.1.4.1.6.2.1.16.0

and i am looking for the other 3.
0
Comment
Question by:kassant7
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
4 Comments
 
LVL 47

Accepted Solution

by:
David earned 2000 total points
ID: 39867051
If you have the MIB file(s), you have the OID.   Just open up the MIB in a text editor and look for it within the file itself.
0
 

Author Comment

by:kassant7
ID: 39867494
I didnt know you could look at the file in a text editor thanks. I open it up and this is what i see;

voltage                OBJECT-TYPE
    SYNTAX                      INTEGER
    ACCESS                      read-only
    STATUS                      optional
    DESCRIPTION                 "Accurate battery terminal voltage in mV, resolution of 1mV"
    ::= { bbuEntry 9 }
autoLearnPeriod                OBJECT-TYPE
    SYNTAX                      INTEGER
    ACCESS                      read-only
    STATUS                      optional
    DESCRIPTION                 "Time (in seconds) between learn cycles (0 to disable auto learn)"
    ::= { bbuEntry 10 }
relStateOfCharge                OBJECT-TYPE
    SYNTAX                      INTEGER(0..100)
    ACCESS                      read-only
    STATUS                      optional
    DESCRIPTION                 "Predicted remaining capacity expressed as % of FullChargeCapacity() (0-100). Value of -1 means not supported"
    ::= { bbuEntry 11 }
capacityRemain                OBJECT-TYPE
    SYNTAX                      INTEGER
    ACCESS                      read-only
    STATUS                      optional
    DESCRIPTION                 "Predicted charge or energy remaining in the battery in joules"
    ::= { bbuEntry 12 }
runTimeToEmpty                OBJECT-TYPE
    SYNTAX                      INTEGER
    ACCESS                      read-only
    STATUS                      optional
    DESCRIPTION                 "Relative gain or loss in remaining life in response to change in power policy represent in minute. Value of -1 means not supported"
    ::= { bbuEntry 13 }
avgTimeToFull                OBJECT-TYPE
    SYNTAX                      INTEGER
    ACCESS                      read-only
    STATUS                      optional
    DESCRIPTION                 "One-minute rolling average of predicted remaining time to full charge. Value of -1 means not supported"
    ::= { bbuEntry 14 }

How do you turn this information into OID's i can use?

Is a there a program that deciphers?
0
 

Author Closing Comment

by:kassant7
ID: 39867703
I didnt know you could read the raw files. Now i am able to find what i was looking for!
0
 
LVL 47

Expert Comment

by:David
ID: 39867765
google MIB editor, there is plenty of free stuff out there.
0

Featured Post

Four New Appliances. Same Industry-leading Speeds.

But don't take it from us.  The Firebox M370 is Miercom tested and Miercom approved, outperforming its competitors for stateless and stateful traffic throughput scenarios.  Learn more about the M370, M470, M570 and M670 and find the right solution for your organization today!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This article is a collection of issues that people face from time to time and possible solutions to those issues. I hope you enjoy reading it.
WARNING:   If you follow the instructions here, you will wipe out your VTP and VLAN configurations.  Make sure you have backed up your switch!!! I recently had some issues with a few low-end Cisco routers (RV325) and I opened a case with Cisco TA…
This tutorial will walk an individual through the process of installing the necessary services and then configuring a Windows Server 2012 system as an iSCSI target. To install the necessary roles, go to Server Manager, and select Add Roles and Featu…
This Micro Tutorial will teach you how to reformat your flash drive. Sometimes your flash drive may have issues carrying files so this will completely restore it to manufacturing settings. Make sure to backup all files before reformatting. This w…
Suggested Courses

770 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question