Solved

VLAN Routing Dell Powerconnect 6224

Posted on 2014-03-16
11
851 Views
Last Modified: 2016-11-23
I having issues routing traffic between VLANs on my Dell PowerConnect 6224.  Attached is the config file.  

I have 3 VLANS 1, 101 & 102
VLAN 1 IP 192.168.1.251/24 (I have followed steps from http://www.dell.com/support/troubleshooting/us/en/19/kcs/kcsarticles/articleview?docid=628735)
VLAN 101 IP 192.168.128.1/24
VLAN 102 IP 192.168.102.1/24

VLAN 1 Host 192.168.1.150
VLAN 102 Host IP 192.168.128.101

I am trying to route traffic between VLAN 1 and VLAN 101.  I can ping VLAN 101's interface ip address from VLAN 1, however I am unable to ping host 192.168.128.101 from VLAN 1.  

If I move VLAN1 host 192.168.1.150 to VLAN 101 and change IP to same subnet range (192.168.128.150) I can successfully ping Host 192.168.128.101.

Any ideas on what I am doing wrong?
config.txt
0
Comment
Question by:tbeck1983
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 6
  • 5
11 Comments
 
LVL 10

Expert Comment

by:Schuyler Dorsey
ID: 39932883
I do not initially see an issue with the config. Did you confirm it wasn't some software blocking the pings on the server itself? E.g. if you are using Symantec, it may have some vlans tagged as trusted and not others.
0
 

Author Comment

by:tbeck1983
ID: 39932894
Even with Symantec disabled I still cannot pint the hosts
0
 
LVL 10

Expert Comment

by:Schuyler Dorsey
ID: 39932912
According to your original post,

VLAN 101 IP 192.168.128.1/24
VLAN 102 Host IP 192.168.128.101

That would put that host in the incorrect vlan for the IP range it is configured in. Or is that a typo?
0
Forrester Webinar: xMatters Delivers 261% ROI

Guest speaker Dean Davison, Forrester Principal Consultant, explains how a Fortune 500 communication company using xMatters found these results: Achieved a 261% ROI, Experienced $753,280 in net present value benefits over 3 years and Reduced MTTR by 91% for tier 1 incidents.

 

Author Comment

by:tbeck1983
ID: 39932921
Sorry that's a typo that host 192.168.128.101 is in VLAN 101
0
 
LVL 10

Expert Comment

by:Schuyler Dorsey
ID: 39932929
On that host, what is the result of trying to ping its default gateway of 192.168.128.1? Can you verify that host has its subnet mask configured to 255.255.255.0?
0
 

Author Comment

by:tbeck1983
ID: 39932940
I have confirmed that the host has its subnet mask configured to 255.255.255.0
0
 
LVL 10

Accepted Solution

by:
Schuyler Dorsey earned 500 total points
ID: 39932942
what is the result of trying to ping its default gateway of 192.168.128.1 from that host 192.168.128.101?
0
 

Author Comment

by:tbeck1983
ID: 39932953
I feel stupid... Default gateway was not set on the host.
0
 
LVL 10

Expert Comment

by:Schuyler Dorsey
ID: 39932954
:)
0
 

Author Comment

by:tbeck1983
ID: 39932956
Thanks for pointing me in the right direction!
0
 

Author Closing Comment

by:tbeck1983
ID: 39932957
Pointed me in the right direction!
0

Featured Post

Free NetCrunch network monitor licenses!

Only on Experts-Exchange: Sign-up for a free-trial and we'll send you your permanent license!

Here is what you get: 30 Nodes | Unlimited Sensors | No Time Restrictions | Absolutely FREE!

Act now. This offer ends July 14, 2017.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

#Citrix #Netscaler #MSSQL #Load Balance
WARNING:   If you follow the instructions here, you will wipe out your VTP and VLAN configurations.  Make sure you have backed up your switch!!! I recently had some issues with a few low-end Cisco routers (RV325) and I opened a case with Cisco TA…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

728 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question