Solved

Riverbed Steelhead Configuration

Posted on 2014-03-19
6
707 Views
Last Modified: 2014-03-20
Hello Experts,

I'm practising configuring Riverbed. I can't seem to get the lan interface to come up.

Could someone please take a look at the configuration and let me know what I'm doing wrong?

Cheers

Carlton
22-38-01--Riverbed-Client-Side-1.txt
0
Comment
Question by:cpatte7372
  • 5
6 Comments
 

Author Comment

by:cpatte7372
ID: 39941051
Experts,

See the following:

servapp # show interfaces lan0_0
Interface lan0_0 state
   Up:                 no
   Interface type:     ethernet
   Speed:              100Mb/s
   Duplex:             full
   MTU:                1500
   HW address:         00:0E:B6:95:A3:0A
   Link:               yes

   RX bytes:           48406
   RX packets:         431
   RX mcast packets:   255
   RX discards:        0
   RX errors:          0
   RX overruns:        0
   RX frame:           0

   TX bytes:           42
   TX packets:         1
   TX discards:        0
   TX errors:          0
   TX overruns:        0
   TX carrier:         0
   TX collisions:      0
servapp #
0
 
LVL 12

Accepted Solution

by:
Infamus earned 500 total points
ID: 39941071
Not sure which one but either try connect WAN0 or InPath0 then LAN0 should come up.
0
 

Author Comment

by:cpatte7372
ID: 39941100
Experts,

When I hard code the interface to 100 Full Duplex I get the following:

servapp # show int lan0_0
Interface lan0_0 state
   Up:                 no
   Interface type:     ethernet
   Speed:              UNKNOWN
   Duplex:             UNKNOWN

   MTU:                1500
   HW address:         00:0E:B6:95:A3:0A
   Link:               no
0
Portable, direct connect server access

The ATEN CV211 connects a laptop directly to any server allowing you instant access to perform data maintenance and local operations, for quick troubleshooting, updating, service and repair.

 

Author Comment

by:cpatte7372
ID: 39941104
Experts,

Even though I get the following showing speed and duplex UNKNOWN

servapp # show int lan0_0
Interface lan0_0 state
   Up:                 no
   Interface type:     ethernet
   Speed:              UNKNOWN
   Duplex:             UNKNOWN

   MTU:                1500
   HW address:         00:0E:B6:95:A3:0A
   Link:               no

I get the following:

servapp # show interfaces lan0_0 configured
Interface lan0_0 configuration
   Enabled:            yes
   DHCP:               no
   Dynamic DNS DHCP:   no
  Speed:              100
   Duplex:             full

   MTU:                1500
servapp #


Weird
0
 

Author Comment

by:cpatte7372
ID: 39941144
Experts,

Interesting thing is, when its not connected the interface shows up:

servapp # show int lan0_0
Interface lan0_0 state
   Up:                 yes
   Interface type:     ethernet
   Speed:              UNKNOWN
   Duplex:             UNKNOWN
   MTU:                1500
   HW address:         00:0E:B6:95:A3:0A
   Link:               no
0
 

Author Closing Comment

by:cpatte7372
ID: 39941832
Brilliant mate. You nailed it.
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Do you have a computer or other electronic gear that is attached to a rat nest of cables, or alternatively have your cables all bundled nice at neat?  If so then read this post to sidstep common pitfalls. When I was a student at DeVry University,…
When posting a question about a Cisco ASA, Cisco Router or Cisco Switch, it can aid diagnosis if a suitably sanitised copy of the config is provided. It is much better to leave as much of the configuration as original as possible, as it could be tha…
Although Jacob Bernoulli (1654-1705) has been credited as the creator of "Binomial Distribution Table", Gottfried Leibniz (1646-1716) did his dissertation on the subject in 1666; Leibniz you may recall is the co-inventor of "Calculus" and beat Isaac…

807 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question