We help IT Professionals succeed at work.

Cisco EEM applet help

cb_it
cb_it asked
on
720 Views
Last Modified: 2014-05-07
I'm new to EEM so please be gentle. I created 2 applets as you can see below. I'm trying to shutdown and interface at 10:15 and then bring it back up 5 minutes later. This did not work. Anything wrong with what I did?

Also, how do I go into the EEM to see what applets are there? Is there some type of view command? Also, how would I edit one of these applets, for example if I wanted to remove the event timer.

router1e#config t
Enter configuration commands, one per line.  End with CNTL/Z.
router1(config)#event manager applet shutdown_port
router1(config-applet)#event timer cron cron-entry "15 10 * * *"
router1(config-applet)#action 010 cli command "enable"
router1(config-applet)#action 020 cli command "config t"
router1(config-applet)#action 030 cli command "int fa0/0"
router1(config-applet)#action 040 cli command "shut"
router1(config-applet)#action 050 cli command "end"^Z
router1#

router1e#config t
Enter configuration commands, one per line.  End with CNTL/Z.
router1(config)#event manager applet noshut_port
router1(config-applet)#event timer cron cron-entry "20 10 * * *"
router1(config-applet)#action 010 cli command "enable"
router1(config-applet)#action 020 cli command "config t"
router1(config-applet)#action 030 cli command "int fa0/0"
router1(config-applet)#action 040 cli command "no shut"
router1(config-applet)#action 050 cli command "end"^Z
router1#
Comment
Watch Question

Author

Commented:
OK, so I found this command
show event manager policy registered

That shows each applet and all of the actions.

I removed the event timer with this command
router1(config-applet)#event none

Now when I manually run the applet I'm getting the following error, any ideas?

router1#event manager run shutdown_port
router1#
.Apr  6 11:31:18.254: FH-TTY::No more VTY line

router1#
.Apr  6 11:31:18.258: %HA_EM-3-FMPD_ERROR: Error executing applet shutdown_port statement 010
router1#
CERTIFIED EXPERT
Commented:
This one is on us!
(Get your first solution completely free - no credit card required)
UNLOCK SOLUTION

Author

Commented:
Thanks for the reply! But that didn't work. Seems like the error is starting right at line 010.

Error executing applet shutdown_port statement 010

How do I clear sessions from previous EEM executions??

Thanks again.

Author

Commented:
Thanks for the note on clearing user sessions. I rebooted the server and now the applet works fine. Must have been something with the user sessions.

Gain unlimited access to on-demand training courses with an Experts Exchange subscription.

Get Access
Why Experts Exchange?

Experts Exchange always has the answer, or at the least points me in the correct direction! It is like having another employee that is extremely experienced.

Jim Murphy
Programmer at Smart IT Solutions

When asked, what has been your best career decision?

Deciding to stick with EE.

Mohamed Asif
Technical Department Head

Being involved with EE helped me to grow personally and professionally.

Carl Webster
CTP, Sr Infrastructure Consultant
Empower Your Career
Did You Know?

We've partnered with two important charities to provide clean water and computer science education to those who need it most. READ MORE

Ask ANY Question

Connect with Certified Experts to gain insight and support on specific technology challenges including:

  • Troubleshooting
  • Research
  • Professional Opinions
Unlock the solution to this question.
Join our community and discover your potential

Experts Exchange is the only place where you can interact directly with leading experts in the technology field. Become a member today and access the collective knowledge of thousands of technology experts.

*This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

OR

Please enter a first name

Please enter a last name

8+ characters (letters, numbers, and a symbol)

By clicking, you agree to the Terms of Use and Privacy Policy.