Solved

L3 Etherchannel

Posted on 2014-07-26
7
363 Views
Last Modified: 2014-07-27
In a etherchannel all configurations which are done on interface port-channel XX will be passed down to my physically port members automatically is this correct.
0
Comment
Question by:ciscosupp
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 4
  • 3
7 Comments
 
LVL 50

Expert Comment

by:Don Johnston
ID: 40221945
Correct. For all commands that are not specific to port channel or physical interfaces.  For example, "speed" is not one of those commands that get inherited.

But defining access vs. trunk, or which VLANs are allowed on at trunk, those do get inherited by the physical interface.
0
 

Author Comment

by:ciscosupp
ID: 40221957
ok but what I don't understand is I added the command vrf member TEST to my ether channel but when I do show run inter the command is not on my physical interferences which is part of the port channel.



inter face port-channel 10
no switchport
vrf member TEST
ip address 192.168.0.1 255.255.255.0

interface eth1/10
no switchport
channel-group 10 mode active

interface eth1/11
no switchport
channel-group 10 mode active

I can add the command vrf member TEST to the physically interface (etj1/10 -11)without getting any error but my question is why is the command not passed down automatically from etherchannel 10
0
 
LVL 50

Expert Comment

by:Don Johnston
ID: 40222057
Are you doing this on a Nexus platform?
0
Manage your data center from practically anywhere

The KN8164V features HD resolution of 1920 x 1200, FIPS 140-2 with level 1 security standards and virtual media transmissions at twice the speed. Built for reliability, the KN series provides local console and remote over IP access, ensuring 24/7 availability to all servers.

 

Author Comment

by:ciscosupp
ID: 40222241
yes correct  nexus 5548.
I want a L3 port-channel that is part of a vrf.
0
 
LVL 50

Expert Comment

by:Don Johnston
ID: 40222394
I've setup L3 port channels on 7Ks that were not part of the default VRF.  I just don't recall if the command shows on the physical interface.

Unfortunately, I don't have access to that switch right now so I can't check it.

Is it not working or is it working and you're just curious why it's not showing on the physical interfaces?
0
 

Author Comment

by:ciscosupp
ID: 40222454
it working just curious why not showing .
I cant harm when adding the command also to physical interface is this correct.
0
 
LVL 50

Accepted Solution

by:
Don Johnston earned 500 total points
ID: 40222491
it working just curious why not showing
Can't answer that one.  To be honest, it doesn't surprise me. Nexus switches have quite a few idiosyncrasies like that.
I cant harm when adding the command also to physical interface is this correct.
I would not make that assumption. :-0
If you're going to do that, make sure you do it during a maintenance window.
0

Featured Post

Turn your laptop into a mobile console!

The CV211 Laptop USB Console Adapter provides a direct Laptop-to-Computer connection for fast and easy remote desktop access with no software to install.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

AWS has developed and created its highly available global infrastructure allowing users to deploy and manage their estates all across the world through the use of the following geographical components   RegionsAvailability ZonesEdge Locations  Wh…
We recently endured a series of broadcast storms that caused our ISP to shut us down for brief periods of time. After going through a multitude of tests, we determined that the issue was related to Intel NIC drivers on some new HP desktop computers …
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
There's a multitude of different network monitoring solutions out there, and you're probably wondering what makes NetCrunch so special. It's completely agentless, but does let you create an agent, if you desire. It offers powerful scalability …

724 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question