Solved

HP 2910 Set Time

Posted on 2014-09-16
4
1,040 Views
Last Modified: 2014-09-24
Im sure i have set this in the past, but both my hp poe switches date/time are wrong.
I have SNTP setup on one of them.

How can i set the time correctly?

THAnks
0
Comment
Question by:CHI-LTD
  • 3
4 Comments
 
LVL 27

Accepted Solution

by:
Predrag Jovic earned 500 total points
ID: 40325554
Router# config t
Router(config)# ntp server X.X.X.X
Router(config)# exit

to verify association
Router>show ntp associations
0
 
LVL 1

Author Comment

by:CHI-LTD
ID: 40325623
its an hp switch not router.  the show command fails
0
 
LVL 1

Author Comment

by:CHI-LTD
ID: 40328159
Here are the settings/status:

Running configuration:

; J9148A Configuration Editor; Created on release #W.15.08.0012
; Ver #02:11.05:16
hostname "HP-E2910al-48G-PoE"
module 1 type j9148a
mirror-port 5
power-over-ethernet pre-std-detect
qos type-of-service diff-services
sntp server priority 1 194.35.252.7
sntp server priority 2 81.168.77.149
ip authorized-managers 172.19.0.0 255.255.0.0 access manager
ip authorized-managers 172.16.0.0 255.255.0.0 access manager
ip authorized-managers 10.255.255.0 255.255.255.128 access manager
ip authorized-managers 192.168.2.0 255.255.255.0 access manager
ip authorized-managers 192.168.3.0 255.255.255.0 access manager
ip authorized-managers 10.255.254.0 255.255.255.128 access manager
ip authorized-managers 192.168.100.0 255.255.255.0 access manager
ip default-gateway 172.19.10.15
no ip icmp redirects
ip route 0.0.0.0 0.0.0.0 172.19.10.15
ip routing
interface 1
   name "to HP1910 (top)"
   no power-over-ethernet
   exit
interface 2
   name "tp HP1910 (bottom)"
   no power-over-ethernet
   exit
interface 3
   name "to ASA 5505 fe01"
   no power-over-ethernet
   exit
interface 4
   name "Cisco_AP_172.19.3.20"
   exit
interface 5
   no power-over-ethernet
   exit
interface 6
   no power-over-ethernet
   exit
interface 7
   name "Shoretel E1k"
   speed-duplex 100-full
   exit
interface 8
   name "Shoretel SG90"
   speed-duplex 100-full
   exit
interface 9
   name "Shoretel SG90Bri"
   speed-duplex 100-full
   exit
interface 10
   name "chi-Oaisys"
   exit
interface 11
   name "Shoretel HQ"
   exit
interface 12
   name "Ingate"
   exit
snmp-server community "public" unrestricted
snmp-server contact "IT"
vlan 1
   name "DEFAULT_VLAN"
   no untagged 7-48
   untagged 1-6
   ip address 172.19.4.5 255.255.0.0
   exit
vlan 20
   name "Voice"
   untagged 7-48
   ip address 172.16.4.5 255.255.0.0
   ip helper-address 172.19.10.17


HP-E2910al-48G-PoE(config)# show time
Mon Jun 25 06:10:45 1990
HP-E2910al-48G-PoE(config)# show sntp

 SNTP Configuration

  SNTP Authentication : Disabled
  Time Sync Mode: Timep
  SNTP Mode : Broadcast
  Poll Interval (sec) [720] : 720
  Source IP Selection: Outgoing Interface


  Priority SNTP Server Address                      Version Key-id
  -------- ---------------------------------------  ------- ----------
  1        194.35.252.7                             3       0
  2        81.168.77.149                            3       0

HP-E2910al-48G-PoE(config)#

You can see the time is wrong ,.
0
 
LVL 1

Author Closing Comment

by:CHI-LTD
ID: 40341258
needed some tweeking
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Switch Uplinking Arista to Force 10 5 39
Setting up a VPN 60 144
Accessing SQL Server Instance from outside the network 29 112
Why does my public IP keep changing? 6 64
Shadow IT is coming out of the shadows as more businesses are choosing cloud-based applications. It is now a multi-cloud world for most organizations. Simultaneously, most businesses have yet to consolidate with one cloud provider or define an offic…
When you try to share a printer , you may receive one of the following error messages. Error message when you use the Add Printer Wizard to share a printer: Windows could not share your printer. Operation could not be completed (Error 0x000006…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Here's a very brief overview of the methods PRTG Network Monitor (https://www.paessler.com/prtg) offers for monitoring bandwidth, to help you decide which methods you´d like to investigate in more detail.  The methods are covered in more detail in o…

832 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question