EESky
asked on
Can not login AP and configure it ---- Cisco Air-Lap1142
Hi Expert
I am trying to configure AP ---- cisco Air-Lap1142. After I plugged in cable and console, I can see the booting process, but it remain in the following status, and my keyborad and mouse can not control that following message.
even if i hit enter button in my keyboard, the console can not show any change. Any expert can give some suggestion ? Thank you.
I am trying to configure AP ---- cisco Air-Lap1142. After I plugged in cable and console, I can see the booting process, but it remain in the following status, and my keyborad and mouse can not control that following message.
even if i hit enter button in my keyboard, the console can not show any change. Any expert can give some suggestion ? Thank you.
*Oct 23 20:02:02.420: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 23 20:02:03.417: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 23 20:02:03.442: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 23 20:02:03.455: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Oct 23 20:02:03.459: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Oct 23 20:02:04.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 23 20:02:04.454: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Oct 23 20:02:04.480: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 23 20:02:04.489: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 23 20:02:04.494: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 23 20:02:05.480: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Oct 23 20:02:05.489: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 23 20:02:05.517: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 23 20:02:06.617: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 23 20:02:06.624: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 23 20:02:07.641: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 23 20:02:07.652: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Oct 23 20:02:07.656: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Oct 23 20:02:08.641: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 23 20:02:08.651: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Oct 23 20:02:08.678: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 23 20:02:08.690: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 23 20:02:08.694: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 23 20:02:09.678: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Oct 23 20:02:09.689: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 23 20:02:09.717: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 23 20:02:10.717: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 23 20:02:11.511: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
., 1)23 20:07:39.024: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_ECHO_REQUEST
*Oct 23 20:07:50.710: %EVT-4-WRN: Write of flash:/event.capwap done
*Oct 23 20:07:50.737: %LWAPP-3-CLIENTERRORLOG: Switching to Standalone mode
*Oct 23 20:07:50.741: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Oct 23 20:07:50.742: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.60.31.4:5246
*Oct 23 20:07:50.792: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
*Oct 23 20:08:00.798: %CAPWAP-3-ERRORLOG: Selected MWAR 'USSECWLC11'(index 0).
*Oct 23 20:08:00.798: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 23 20:07:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.60.31.4 peer_port: 5246
*Oct 23 20:07:51.453: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.60.31.4 peer_port: 5246
*Oct 23 20:07:51.454: %CAPWAP-5-SENDJOIN: sending Join Request to 10.60.31.4
*Oct 23 20:07:56.454: %CAPWAP-5-SENDJOIN: sending Join Request to 10.60.31.4
*Oct 23 20:07:57.570: Starting Ethernet promiscuous mode
*Oct 23 20:07:57.872: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
*Oct 23 20:07:58.084: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller USSECWLC11
*Oct 23 20:07:58.135: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Oct 23 20:07:58.135: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Oct 23 20:07:58.136: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
*Oct 23 20:07:58.137: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration file
*Oct 23 20:07:58.137: %LWAPP-3-CLIENTERRORLOG: Switching to Connected mode
*Oct 23 20:08:02.667: %WIDS-6-ENABLED: IDS Signature is loaded and enabledASKER
Thank you so much for your fast reply. You are right. This is lightweight AP. What I want to do is to change it into autonomous AP. Now I have several this kind of AP. All of them are disconnected with wireless controller. So, how can I change it into autonomous AP without wireless controller ?
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
Thank you so much for your fast reply. You are right. After I uploaded ios, how can I confirm it is autonomous mode ?
SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
Thanks you! craigbeck,
I also found these features, and i put here for my recording
Following are the three type of IOS available & need to download the correct type before starting the conversion process.
k9w7 – autonomous IOS
k9w8 – full lightweight IOS (this is what is bundled in the WLC .aes image, and is factory installed on “mesh” APs)
rcvk9w8 – lightweight recovery image – this is factory installed on lightweight APs, unless a “mesh” image is specified; it lacks radio firmware
I also found these features, and i put here for my recording
Following are the three type of IOS available & need to download the correct type before starting the conversion process.
k9w7 – autonomous IOS
k9w8 – full lightweight IOS (this is what is bundled in the WLC .aes image, and is factory installed on “mesh” APs)
rcvk9w8 – lightweight recovery image – this is factory installed on lightweight APs, unless a “mesh” image is specified; it lacks radio firmware
You need to log in to your WLC (USSECWLC11) to configure the AP.