Solved

Editing Route Maps on Cisco Router 2821

Posted on 2014-10-28
3
403 Views
Last Modified: 2014-10-30
We would like to match router 2 (cts_nc_r2) with router 1 (cts_nc_r1): How would we edit the route map on R2 to R1?

cts_nc_r2#show route
route-map GPAccess, permit, sequence 10
  Match clauses:
    ip address (access-lists): 199
  Set clauses:
    ip next-hop 10.1.0.218
    interface GigabitEthernet0/0.1
  Policy routing matches: 0 packets, 0 bytes


cts_nc_r1#show route
route-map GPAccess, permit, sequence 10
  Match clauses:
    ip address (access-lists): 199
  Set clauses:
    ip next-hop 10.100.200.14
    interface FastEthernet0/3/0
  Policy routing matches: 6686457 packets, 678231057 bytes
route-map GPAcess, permit, sequence 10
  Match clauses:
  Set clauses:
  Policy routing matches: 0 packets, 0 bytes
0
Comment
Question by:FRANK EGGLESTON
  • 2
3 Comments
 
LVL 50

Expert Comment

by:Don Johnston
Comment Utility
We would like to match router 2 (cts_nc_r2) with router 1 (cts_nc_r1):
What do you mean by this?
Do you want the same route map on both routers?  If so, it looks like the only difference is the next hop address. You won't be to have that be the same unless both routers share a common network with that address.
0
 

Author Comment

by:FRANK EGGLESTON
Comment Utility
Hi! Yes both routers are on the same network using GLBP. We inherited the configurations from a previous network engineer. I want to edit the next hop address to 10.1.0.218 but did not want to break anything.

Steven
0
 
LVL 50

Accepted Solution

by:
Don Johnston earned 500 total points
Comment Utility
Okay. Then on the cts_nc_r1 router do the following:

route-map GPAccess, permit, sequence 10
  Set clauses:
    ip next-hop 10.1.0.218
    interface GigabitEthernet0/0.1 ! or whatever interface the 10.1.0.218 is connected to.

Open in new window


IIRC, that should overwrite the existing statements.  But if it doesn't, just followup with "no" in front of the old statements:

route-map GPAccess, permit, sequence 10
    no ip next-hop 10.1.0.218
    no interface GigabitEthernet0/0.1

Open in new window

0

Featured Post

What Is Threat Intelligence?

Threat intelligence is often discussed, but rarely understood. Starting with a precise definition, along with clear business goals, is essential.

Join & Write a Comment

Suggested Solutions

Title # Comments Views Activity
FortiGate problem 8 72
IPhone using PC internet 17 44
Wireshark 7 52
one station on the LAN appears with 10 mbps speed 3 46
The DSL Parameters part of this article is valid and can be considered with any brand of internet router and modem (Dlink, 3com, Alcatel, Usrobotics, Parks), by accessing the configuration interface available by the manufacturer eg: http://10.1.1.1 …
#Citrix #Citrix Netscaler #HTTP Compression #Load Balance
Get a first impression of how PRTG looks and learn how it works.   This video is a short introduction to PRTG, as an initial overview or as a quick start for new PRTG users.
In this tutorial you'll learn about bandwidth monitoring with flows and packet sniffing with our network monitoring solution PRTG Network Monitor (https://www.paessler.com/prtg). If you're interested in additional methods for monitoring bandwidt…

762 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

6 Experts available now in Live!

Get 1:1 Help Now