Solved

Access to shares when vpn established

Posted on 2014-12-01
5
50 Views
Last Modified: 2016-02-03
Hi,

I need help solving an issue regarding VPN.
I have a router adsl from Vodafone, a techinicolotr tg582n which are connected via lan to a juniper ssg20 which is proxy and firewall. Internally clients use the juniper to connect to internet, receive mail, etc....
The juniper has a vpn configured.
The problem is when i established a vpn can't access to shares or any servers.
I've tried create a route in the router of vodafone, but still can't access to shares.
The vodafone router is in 192.168.1.xxx, the juniper is in 192.168.0.xxx, and the vpn uses the ip 192.168.254.xxx.

What's new it's the vodafone router, so i think isn't necessary change anything in juniper?

Thanks.

Best regards.
0
Comment
Question by:TLatas
  • 3
  • 2
5 Comments
 
LVL 5

Expert Comment

by:Abdul Khadja Alaoudine
ID: 40473531
Assuming routing configured correctly between VPN and Internal networks, on Juniper you need to allow ports for file share access between VPN and internal network (where the file server is?). If it is Windows file server see following for list of ports:

http://technet.microsoft.com/en-us/library/cc731402.aspx

Below is for Microsoft products:
http://technet.microsoft.com/en-us/library/cc875824.aspx
0
 

Author Comment

by:TLatas
ID: 40473660
Hi Abdul,

Thanks for your reply.
One question, those ports should be configured in juniper or in adsl router?
I ask this, because, in past, one month ago, when vodafone changed his router, we can access vpn and shares, so probably those ports are opening or permited in juniper.

Best regards.
0
 
LVL 5

Expert Comment

by:Abdul Khadja Alaoudine
ID: 40473799
If the router provided by Vodafone has built in Firewall then ports must be allowed on them as well. Check Juniper to ensure the ports are allowed and it has correct IP address for router provided by Vodafone. If connection still fails monitor logs on Juniper (and also on Vodafone device if possible) to see where it is being blocked.
0
 

Author Comment

by:TLatas
ID: 40474044
Hi,
I'll try provide the ports, those weren't provided.

How can i check the ports in juniper? The juniper is a ssg20.

Thanks.

Best regards.
0
 
LVL 5

Accepted Solution

by:
Abdul Khadja Alaoudine earned 500 total points
ID: 40475418
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Short answer to this question: there is no effective WiFi manager in iOS devices as seen in Windows WiFi or Macbook OSx WiFi management, but this article will try and provide some amicable solutions to better suite your needs.
How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
Viewers will learn how to connect to a wireless network using the network security key. They will also learn how to access the IP address and DNS server for connections that must be done manually. After setting up a router, find the network security…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

772 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question