Solved

Exchange 2007 (part of SBS 2008) Problem after installing Roll Up 15 for Exchange SP3

Posted on 2014-12-14
6
506 Views
Last Modified: 2014-12-20
Hi,
So I decide to do Windows updates on Small Business Server 2008, including a roll up for Exchange.
Previous Roll ups have been installed no problem.

I installed rollup 15, as recommended by Windows update.

After the updates are done, I email a couple accounts and I get the exact same error:


OK rejected your message to the following email addresses:

2ndfloor@myemail.ca (2ndfloor@myemail.ca)


OK gave this error:
No description

A problem occurred while delivering this message to this email address. Try sending this message again. If the problem continues, please contact your helpdesk.

Diagnostic information for administrators:

Generating server: Lisa.mycompany.ca

2ndfloor@myemail.ca
OK #550 No description ##

Original message headers:


So I can send out with no problems.

DNS for the mail record is fine and our External IP has not changed.

I tried sending to other accounts and from my Yahoo address and there is no change.
Spam filter is Exchange an is on and SCL is set to 5, but I don't think it's making it that far.  Since the email is bouncing back and not be forwarded to the Spam catch all account on the Small Business Server.

So I went into the Server and uninstalled the roll up , but it still does the exact same thing (left all other updates in for now).

Any suggestions would be helpful, as this is a production server.

Thank you
0
Comment
Question by:2ndFloor
6 Comments
 

Author Comment

by:2ndFloor
ID: 40499321
Hi Just Reviewed the system logs and here are two interesting entries:

Event ID: 1032
Receive connector 192.168.0.2:25 requires Transport Layer Security (TLS) before the MailFrom command can be run, but the server can't achieve it. Check the authentication settings of this connector.

Event ID: 1032
Receive connector 127.0.0.1:25 requires Transport Layer Security (TLS) before the MailFrom command can be run, but the server can't achieve it. Check the authentication settings of this connector.

On another EE issue, someone recommends installing a fix made for Vista 64 bit, 372273_intl_x64_zip.exe, from Microsoft's website, anyone use it?
0
 
LVL 12

Expert Comment

by:Imtiaz Hasham
ID: 40499351
I would revisit the connectors to ensure nothing changed after deploying the ru
0
 
LVL 22

Expert Comment

by:David Atkin
ID: 40499836
Hello,

Run the Fix My Network wizard in the SBS Console, this should detect and repair the error with the Exchange connectors.
0
Control application downtime with dependency maps

Visualize the interdependencies between application components better with Applications Manager's automated application discovery and dependency mapping feature. Resolve performance issues faster by quickly isolating problematic components.

 
LVL 20

Expert Comment

by:Satya Pathak
ID: 40499838
well as per event ID 1032 its looks like recive connector issue .

Go through the below KB and try to set the value of receive connector  $true

http://www.microsoft.com/technet/support/ee/transform.aspx?ProdName=Exchange&ProdVer=8.0&EvtID=1032&EvtSrc=MSExchangeTransport
0
 

Accepted Solution

by:
2ndFloor earned 0 total points
ID: 40500901
Hi everyone,
I already ran the Fix my Network wizard and it didn't find any problems with the network other than a warning about DNS using forwarding and not root hints.

I disabled the 4 receive connectors and recreated it and it seemed to have worked.

Thanks everyone!
0
 

Author Closing Comment

by:2ndFloor
ID: 40510622
I selected my own comment because I fixed it on my own within a couple hours of the post.  I thank everyone for helping though!
0

Featured Post

Don't lose your head updating email signatures!

Do your end users still have the wrong email signature? Do email signature updates bore you or fill you with a sense of dread? You can make this a whole lot easier on yourself by trusting an Exclaimer email signature management solution. Over 50 million users do...so should you!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Local Continuous Replication is a cost effective and quick way of backing up Exchange server data. The following article describes the steps required to configure Local Continuous Replication. Also, the article tells you how to restore from a backup…
Follow this checklist to learn more about the 15 things you should never include in an email signature from personal quotes, animated gifs and out-of-date marketing content.
In this video we show how to create a User Mailbox in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.: First we need to log into the Exchange Admin Center. Navigate to the Recipients >> Mailb…
To show how to create a transport rule in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.: First we need to log into the Exchange Admin Center. Navigate to the Mail Flow >> Rules tab.:  To cr…

920 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

16 Experts available now in Live!

Get 1:1 Help Now