Solved

vagrant box not showing up on virtual box

Posted on 2015-01-11
9
798 Views
Last Modified: 2015-02-28
bash-3.2# vagrant up
Bringing machine 'default' up with 'virtualbox' provider...
==> default: Clearing any previously set forwarded ports...
==> default: Clearing any previously set network interfaces...
==> default: Preparing network interfaces based on configuration...
    default: Adapter 1: nat
==> default: Forwarding ports...
    default: 22 => 2222 (adapter 1)
==> default: Booting VM...
==> default: Waiting for machine to boot. This may take a few minutes...
    default: SSH address: 127.0.0.1:2222
    default: SSH username: vagrant
    default: SSH auth method: private key
    default: Warning: Connection timeout. Retrying...
==> default: Machine booted and ready!
GuestAdditions 4.3.20 running --- OK.
==> default: Checking for guest additions in VM...
==> default: Mounting shared folders...
    default: /vagrant => /firstVM
==> default: Machine already provisioned. Run `vagrant provision` or use the `--provision`
==> default: to force provisioning. Provisioners marked to run always will still run.
0
Comment
Question by:linuxperson
  • 5
  • 4
9 Comments
 
LVL 62

Expert Comment

by:gheist
ID: 40543360
I;d stop vagrant and check what machine shows in user interface.
0
 

Author Comment

by:linuxperson
ID: 40548133
I am trying to delete what i had and want to try from scratch.

I am getting  509 error

bash-3.2# vagrant box add testbox https://dl.dropboxusercontent.com/u/29173892/vagrant-boxes/debian7.3.0-vbox4.3.6-puppet3.4.1.box
==> box: Adding box 'testbox' (v0) for provider:
    box: Downloading: https://dl.dropboxusercontent.com/u/29173892/vagrant-boxes/debian7.3.0-vbox4.3.6-puppet3.4.1.box
An error occurred while downloading the remote file. The error
message, if any, is reproduced below. Please fix this error and try
again.

The requested URL returned error: 509 Bandwidth Error
0
 

Author Comment

by:linuxperson
ID: 40548279
bash-3.2# vagrant up  
Bringing machine 'default' up with 'virtualbox' provider...
==> default: Checking if box 'hashicorp/precise32' is up to date...
==> default: Clearing any previously set forwarded ports...
==> default: Clearing any previously set network interfaces...
==> default: Preparing network interfaces based on configuration...
    default: Adapter 1: nat
==> default: Forwarding ports...
    default: 22 => 2222 (adapter 1)
==> default: Booting VM...
==> default: Waiting for machine to boot. This may take a few minutes...
    default: SSH address: 127.0.0.1:2222
    default: SSH username: vagrant
    default: SSH auth method: private key
    default: Warning: Connection timeout. Retrying...
==> default: Machine booted and ready!
GuestAdditions 4.3.20 running --- OK.
==> default: Checking for guest additions in VM...
==> default: Mounting shared folders...
    default: /vagrant => /private/var/root/code/sandbox/vagrant
==> default: Machine already provisioned. Run `vagrant provision` or use the `--provision`
==> default: to force provisioning. Provisioners marked to run always will still run.


when i went to open the virtual box, I don't see the VM.  clearly its shows virtual box is my provider.

not sure why is not showing up Oracle Virtual Box.
0
Complete VMware vSphere® ESX(i) & Hyper-V Backup

Capture your entire system, including the host, with patented disk imaging integrated with VMware VADP / Microsoft VSS and RCT. RTOs is as low as 15 seconds with Acronis Active Restore™. You can enjoy unlimited P2V/V2V migrations from any source (even from a different hypervisor)

 
LVL 62

Expert Comment

by:gheist
ID: 40548365
According to output VM was provisioned for root user.Normally one runs most of desktop as diffrent user.
0
 

Author Comment

by:linuxperson
ID: 40565394
what makes different if i run as different user? let me know
0
 
LVL 62

Accepted Solution

by:
gheist earned 500 total points
ID: 40565534
Each user has their own set of virtualbox configuration.
0
 

Author Comment

by:linuxperson
ID: 40594452
I am running as root
0
 
LVL 62

Expert Comment

by:gheist
ID: 40595222
Very insecure...
0
 

Author Comment

by:linuxperson
ID: 40609937
How can i setup as different user
0

Featured Post

Complete VMware vSphere® ESX(i) & Hyper-V Backup

Capture your entire system, including the host, with patented disk imaging integrated with VMware VADP / Microsoft VSS and RCT. RTOs is as low as 15 seconds with Acronis Active Restore™. You can enjoy unlimited P2V/V2V migrations from any source (even from a different hypervisor)

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
linux(debian) mouse poor performance 4 62
Web resource - Man pages for SUSE Enterprise Linux 11 1 41
Intel fortran compiler (ifort) 5 38
Linux MD5 Hash 7 37
There is an easy way, in .NET, to centralize the treatment of all unexpected errors. First of all, instead of launching the application directly in a Form, you need first to write a Sub called Main, in a module. Then, set the Startup Object to th…
This article is meant to give a basic understanding of how to use R Sweave as a way to merge LaTeX and R code seamlessly into one presentable document.
Connecting to an Amazon Linux EC2 Instance from Windows Using PuTTY.
The viewer will learn how to use the return statement in functions in C++. The video will also teach the user how to pass data to a function and have the function return data back for further processing.

839 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question