Solved

Cisco ASA 5515 default login

Posted on 2015-01-15
6
185 Views
Last Modified: 2015-01-19
I have an ASA 5515 and I was able to get into it with ADSM and I was able to reset the config to factory defaults so I can repurpose the device.

When going back in after the reset, the usual cisco/cisco username and password are not working.

I added the device cert to my java cert list, added the site to trusted site, etc but it keeps prompting me for the username and password when i enter the default of cisco/cisco.

Thoughts?  By the way, CLI is not an option for me.

:)  I'm just throwing that out there.

Thanks

Cliff
0
Comment
Question by:crp0499
  • 3
  • 3
6 Comments
 
LVL 17

Expert Comment

by:Spartan_1337
ID: 40552167
Did you get to the ASDM web page? If so, then just click on the Run startup wizard and setup with no username or password.
0
 

Author Comment

by:crp0499
ID: 40552202
i get the page that allows me to download asdm or use web start
0
 
LVL 17

Expert Comment

by:Spartan_1337
ID: 40552224
OK. If you did what you described then it reset the config, not the user accounts. Can you try your user account to see if you can get in?
0
Why You Should Analyze Threat Actor TTPs

After years of analyzing threat actor behavior, it’s become clear that at any given time there are specific tactics, techniques, and procedures (TTPs) that are particularly prevalent. By analyzing and understanding these TTPs, you can dramatically enhance your security program.

 

Author Comment

by:crp0499
ID: 40552256
No user account works, AND, now, after a reboot, the mgt port is showing no connectivity and no activity.  no lights on ASA or switch.  Before reboot, I could get to the https://192.168.1.1 page.  Now, nadda.

I fear I may have hosed it in the middle of the reset, but I did wait 15 mins before power cycle.
0
 
LVL 17

Accepted Solution

by:
Spartan_1337 earned 500 total points
ID: 40553279
It is possible the management port is shutdown but at this point, you will need to get CLI access. I know you stated you don't have it but it is in your best interest to get CLI access for this device.
0
 

Author Closing Comment

by:crp0499
ID: 40558819
used cli, reset to factory defaults, done.
0

Featured Post

Find Ransomware Secrets With All-Source Analysis

Ransomware has become a major concern for organizations; its prevalence has grown due to past successes achieved by threat actors. While each ransomware variant is different, we’ve seen some common tactics and trends used among the authors of the malware.

Join & Write a Comment

Overview The Cisco PIX 501, PIX 506e, ASA 5505 and ASA 5510 (most if not all of this information will be relevant to the PIX 515e but I do not have a working configuration handy to verify the validity) are primarily used within small to medium busi…
This article assumes you have at least one Cisco ASA or PIX configured with working internet and a non-dynamic, public, address on the outside interface. If you need instructions on how to enable your device for internet, or basic configuration info…
Illustrator's Shape Builder tool will let you combine shapes visually and interactively. This video shows the Mac version, but the tool works the same way in Windows. To follow along with this video, you can draw your own shapes or download the file…
You have products, that come in variants and want to set different prices for them? Watch this micro tutorial that describes how to configure prices for Magento super attributes. Assigning simple products to configurable: We assigned simple products…

758 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

21 Experts available now in Live!

Get 1:1 Help Now