[Last Call] Learn about multicloud storage options and how to improve your company's cloud strategy. Register Now

x
?
Solved

Static route for new data line.

Posted on 2015-01-27
3
Medium Priority
?
131 Views
Last Modified: 2015-02-02
I have two sites (primary -1 and a colocation - 2). We are moving one of our data lines from primary to colocation. I have routes set up in the colocation to route traffic back to the primary site. I would just need to reverse this config for the data line move correct? I can provide config if necessary.

This is the current setup. VLAN 8 at the primary is the route for the line. the 10.x.x.x is where the traffic goes. Just to preface this, we are running VDI's that are located at the colocation site. We also have virtual servers that are located there. Basically about 90% of our environment is at the colocation and is routed back to the primary site.  Let me know if this makes sense. It is an MPLS route.

Thanks

Colocation:

interface vlan.0.10
  ip address 10.50.50.225 255.255.255.0 primary
  no shutdown
  exit

ip address 172.22.5.225 255.255.255.0 primary
  ip access-group 100 in
  ip helper-address 172.22.100.17
  no shutdown
  exit

 ip route 0.0.0.0/0 172.22.5.130 interface vlan.0.100 1
 ip route 10.101.0.0/16 10.50.50.1 interface vlan.0.10 1
 ip route 10.101.4.0/24 10.50.50.1 interface vlan.0.10 1
 ip route 10.103.0.0/16 10.50.50.1 interface vlan.0.10 1
 ip route 10.103.4.0/24 10.50.50.1 interface vlan.0.10 1
 ip route 10.115.0.0/16 10.50.50.1 interface vlan.0.10 1
 ip route 10.116.0.0/16 10.50.50.1 interface vlan.0.10 1


Primary:

 interface vlan.0.8
  ip address 172.22.6.225 255.255.255.0 primary
  no shutdown
  exit

interface vlan.0.12
  ip address 10.50.50.1 255.255.255.0 primary
  no shutdown
  exit


 ip route 0.0.0.0/0 10.50.50.225 interface vlan.0.12 1
 ip route 10.101.0.0/16 172.22.6.215 interface vlan.0.8 1
 ip route 10.101.4.0/24 172.22.6.215 interface vlan.0.8 1
 ip route 10.103.0.0/16 172.22.6.215 interface vlan.0.8 1
 ip route 10.103.4.0/24 172.22.6.215 interface vlan.0.8 1
 ip route 10.115.0.0/16 172.22.6.215 interface vlan.0.8 1
 ip route 10.116.0.0/16 172.22.6.215 interface vlan.0.8 1



I am guessing that all I just have to create a vlan interface for the new line and route the  10.x.x.x traffic to it since it is all at the colocation site now. Plus remove the one route for the 172.22.6.0 traffic at the colo that points back to the primary site. Correct? Just trying to verify, thanks
0
Comment
Question by:DDCO
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 18

Accepted Solution

by:
John Gates, CISSP earned 2000 total points
ID: 40575066
I believe you are correct on both points.  

-D-
0
 

Author Closing Comment

by:DDCO
ID: 40585155
Thanks for taking a look and confirming what I was thinking.
0
 
LVL 18

Expert Comment

by:John Gates, CISSP
ID: 40585173
You're welcome.  Thanks for your response :-)
0

Featured Post

Veeam Task Manager for Hyper-V

Task Manager for Hyper-V provides critical information that allows you to monitor Hyper-V performance by displaying real-time views of CPU and memory at the individual VM-level, so you can quickly identify which VMs are using host resources.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

In this article, I am going to show you how to simulate a multi-site Lab environment on a single Hyper-V host. I use this method successfully in my own lab to simulate three fully routed global AD Sites on a Windows 10 Hyper-V host.
WARNING:   If you follow the instructions here, you will wipe out your VTP and VLAN configurations.  Make sure you have backed up your switch!!! I recently had some issues with a few low-end Cisco routers (RV325) and I opened a case with Cisco TA…
Viewers will learn how to connect to a wireless network using the network security key. They will also learn how to access the IP address and DNS server for connections that must be done manually. After setting up a router, find the network security…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

650 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question