?
Solved

Running IPv6 and IPv4 in parallel

Posted on 2015-02-04
6
Medium Priority
?
175 Views
Last Modified: 2015-02-05
A peripheral requires IPv6 to operate, however my backend is relying on IPv4 setup.

How can I connect my PC to have access to the peripheral and the backend?
0
Comment
Question by:trihoang
  • 4
  • 2
6 Comments
 
LVL 17

Accepted Solution

by:
Sajid Shaik M earned 1500 total points
ID: 40588344
the peripheral connecting to pc is direct or over gateways ... if it's connects over gateways... all devices switches routers etc. should enable the IPV 6 ....

ipv4 and ipv6 both can coexistence ...

see the link
http://www.internetsociety.org/articles/ipv4ipv6-coexistence-and-transition

all the best
0
 

Author Comment

by:trihoang
ID: 40588347
It is a direct connection from the PC to the peripheral

Would it work if I connect the peripheral and backend to a switch?
0
 
LVL 17

Expert Comment

by:Sajid Shaik M
ID: 40588351
the thing is the switch is ipv6 compatible ?
0
Evaluating UTMs? Here's what you need to know!

Evaluating a UTM appliance and vendor can prove to be an overwhelming exercise.  How can you make sure that you're getting the security that your organization needs without breaking the bank? Check out our UTM Buyer's Guide for more information on what you should be looking for!

 
LVL 17

Expert Comment

by:Sajid Shaik M
ID: 40588352
what swich u r using ?
0
 

Author Comment

by:trihoang
ID: 40588359
Switch is a Cisco Small Business SG 200-08
0
 
LVL 17

Expert Comment

by:Sajid Shaik M
ID: 40588375
(what kind of peripheral it is ? ) and how you want to connect to that peripheral...

if u are connecting direct ... then (if the machine is having the latest network card not earlier than 2 years can do auto negotiation of the physical connectivity that means no need of cross cable)

a.      Click "Start", input "NCPA.CPL" (without quotation marks) to Start Search bar and press "Enter".
b.      Right-click the network connection and click "Properties".
If you are prompted for an administrator password or confirmation, type the password or provide confirmation.
c.       Click to highlight "Internet Protocol Version 6 (TCP/IPv6)" and click "Properties".
d.      Check "Obtain an IP address automatically" and "Obtain DNS server address automatically".
e.      Click "OK".
f.        Click to highlight "Internet Protocol Version 4 (TCP/IPv4)" and click "Properties".
g.      Check "Obtain an IP address automatically" and "Obtain DNS server address automatically".
h.      Click "OK".
Reboot the computer.
I would suggest you to perform the troubleshooting steps and run the Fix it from the following article to enable IPV6 protocols.

if it's connecting through Internet Explorer... there using your switch
 
see the link  for more detail..

http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbss/sg200/administration_guide/78-19562.pdf

Starting the Web-Based Switch Configuration Utility
This section describes how to navigate the web-based switch configuration utility.
Browsers have the following restrictions:
• If you are using Internet Explorer 8, open a browser window and configure
the following settings:
Click Tools > Internet Options and then select the Security tab. Select
Local Intranet and click Sites. Click Advanced and then click Add. Add the
intranet address of the switch (http://<ip-address>) to the local intranet
zone. The IP address can also be specified as the subnet IP address, so that
all addresses in the subnet are added to the local intranet zone.
• If you are using Internet Explorer 6, you cannot directly use an IPv6 address
to access the switch. You can, however, use the Domain Name System
(DNS) server to create a domain name that contains the IPv6 address, and
then use that domain name in the address bar in place of the IPv6 address.
• If you have multiple IPv6 interfaces on your management station, use the
IPv6 global address instead of IPv6 link local address to access the switch
from your browser.
0

Featured Post

Free Tool: SSL Checker

Scans your site and returns information about your SSL implementation and certificate. Helpful for debugging and validating your SSL configuration.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
Outsource Your Fax Infrastructure to the Cloud (And come out looking like an IT Hero!) Relative to the many demands on today’s IT teams, spending capital, time and resources to maintain physical fax servers and infrastructure is not a high priority.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
NetCrunch network monitor is a highly extensive platform for network monitoring and alert generation. In this video you'll see a live demo of NetCrunch with most notable features explained in a walk-through manner. You'll also get to know the philos…

607 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question