Solved

Configure HP switch to untag VLANs from VMWare esxi 5.5

Posted on 2015-02-06
5
328 Views
Last Modified: 2015-02-06
Hi,
We have a HP V1910-24G switch which we want to connect to a VMWare host  to be able to *untag* tagged VLANs from VMWare ESXi 5.5.

Example:
HP switch port 24 is connected to VMWare host network adapter with tagged traffic.
VLAN ID 20 from VMWare is untagged to HP switch port 1-8,
VLAN ID 21 is untagged to ports 9-16

The HP switch has so many different VLAN 'flavors' and properties so I want to have this set up as best practice to get the most out of it.  Thanks a lot for helping up with this.

regards Tor
0
Comment
Question by:datator
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 2
5 Comments
 
LVL 50

Expert Comment

by:Don Johnston
ID: 40593541
If I understand you correctly, what you're trying to do is route traffic from one VLAN to another.

What VLANs are tagged on port 24?
0
 

Author Comment

by:datator
ID: 40593560
Hi
VMWare tags VLAN ID 20 and 21 and via the host's network interface this is connected to port 24.  I want this to be untagged (VID 20 to the switch port 1-8 and VID 21 to the switch port 9-16).  Normally this is a piece of cake configuring a switch for VLANs but this HP switch had so many different settings and I just want to get them all correctly set for optimum performance.  If possible with port 23 and 24 trunked for more bandwidth....
regards
Tor
0
 
LVL 50

Accepted Solution

by:
Don Johnston earned 500 total points
ID: 40593565
Okay, I think that got it now.

This is actually default behavior.  Here's what your config will look like:

VLAN 20
 tagged 24
 untagged 1-8
VLAN 21
 tagged 24
 untagged 9-16

Open in new window

0
 

Author Comment

by:datator
ID: 40593679
Hi,
Good.  I have always only configured managed switches via the webinterface.  Is this example using some commandline via the console input or is it via ssh?
Can I use the webinterface to achieve the same thing?
regards
Tor
0
 
LVL 50

Expert Comment

by:Don Johnston
ID: 40593699
Yes.  This is the CLI commands.  It can be done via the web interface as well.
0

Featured Post

Get proactive database performance tuning online

At Percona’s web store you can order full Percona Database Performance Audit in minutes. Find out the health of your database, and how to improve it. Pay online with a credit card. Improve your database performance now!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Creating an OSPF network that automatically (dynamically) reroutes network traffic over other connections to prevent network downtime.
Configuring network clients can be a chore, especially if there are a large number of them or a lot of itinerant users.  DHCP dynamically manages this process, much to the relief of users and administrators alike!
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

622 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question